Whirlpool WDFS3R4NWESG Sense Dishwasher
Daily Reference Guide
EN
THANK YOU FOR BUYING A WHIRLPOOL PRODUCT.
In order to receive a more complete assistance, please
register your appliance on: www.whirlpool.com.hk
Before using the appliance carefully read Safety and Installation
Instructions. More information about your product available on
After installation, please remember to remove all transport protection
parts from the dishwasher.
CONTROL PANEL
1. ON-OFF/Reset button with indicator light
2. PREVIOUS program button
3. NEXT program button
P
4. FAVOURITE program button with indicator light
5. Salt reservoir empty indicator light
6. Rinse Aid reservoir empty indicator light
7. DESCALE indicator light
8. Closed Water tap indicator light
9. Key lock indicator light
10. Program number and remaining time indicator
11. Display
12. Turbo option button with indicator light
11
12
13
1
2
3
4
5 6 7 8 9 10
14
15
16
13. Half Load option button with indicator light/ Settings - 3 sec. press
14. Extra Dry option button with indicator light/ Keylock - 3 sec. press
15. Delay option button with indicator light
16. START/Pause button with indicator light
FIRST TIME USE
SETTING MENU
To change, follow instructions in section“SETTING MENU”.
Only use salt that has been specifically designed for dishwashers.
After the salt has been poured into the machine, the SALT REFILL indicator
light switches off.
1. Switch on the appliance by pressing the ON-OFF button.
2. Hold the Settings (Half Load ) button for 3 seconds, until you hear
a beep and the display shows„SEt”.
If the salt container is not filled, the water softener and the heating
element may be damaged as a result of limescale accumulation.
Use of salt is recommended with any type of dishwasher detergent.
3. After one second the first available setting (letter„h”) will be displayed.
4. Press PREVIOUS /NEXT to scroll through the list of available settings
(see table below), then press START/Pause
value of the currently selected setting.
to view and change the
WATER SOFTENING SYSTEM
5. Press PREVIOUS /NEXT to change the value, then press START/Pause
to save the new value and return to the main menu.
6. To change another setting, repeat points 4 and 5.
Water softener automatically reduces water hardness, consequently preventing
scale buildup on the heater, contributing also to better cleaning efficiency.
This system regenerates itself with salt, therefore it is required to refill
the salt container when empty. The frequency of regeneration depends
on the water hardness level setting - regeneration takes place once per 4-6
Eco cycles with the water hardness level set to 3. The regeneration process
occurs at the beginning of the cycle with additional fresh water.
7. Press ON-OFF or wait 30 seconds to exit the menu.
VALUES
(Default - in bold)
LETTER
SETTING
Water Hardness Level
(see “SETTING THE WATER HARDNESS”
and “WATER HARDNESS TABLE”)
•
•
•
Single regeneration consumes ~3L of water;
Takes up to 5 additional minutes for the cycle;
Consumes below 0.005kWh of energy.
1 | 2 | 3 | 4 | 5
Rinse Aid Level
(see “ADJUSTING THE DOSAGE OF RINSE AID”)
0 | 1 | 2 | 3 | 4 | 5
1 | 0
FILLING THE RINSE AID DISPENSER
Rinse aid makes dish DRYING easier. The rinse aid dispenser A should be
NaturalDry (see “OPTIONS AND FUNCTIONS”)
“1”= On, “0”= Off
filled when the RINSE AID REFILL indicator light in the control panel is lit.
1. Open the dispenser
B
by
Sound
“1”= On, “0”= Off
pressing and pulling up the
tab on the lid.
1 | 0
2. Pour in the rinse aid (max.110
ml), making sure it does not
overflow from the dispenser.
If this happens, clean the spill
immediately with a dry cloth.
Factory Settings
Press START/Pause to restore to the factory
default all the values of the settings included
in the settings menu.
-
A
B
FILLING THE SALT RESERVOIR
The use of salt prevents the formation of LIMESCALE on the dishes and on
the machine’s functional components.
The salt reservoir is located in the lower part of the dishwasher (under
the lower rack on the left side).
3. Press the lid down until you hear a click to close it.
NEVER pour the rinse aid directly into the appliance tub.
ADJUSTING THE DOSAGE OF RINSE AID
If you are not completely satisfied with the drying results, you can adjust
the quantity of rinse aid used.
•
•
•
It is mandatory that the salt reservoir never be empty.
It is important to set the water hardness.
Salt must be filled when the SALT REFILL indicator light
panel is lit.
To change, follow the instructions in the section “SETTING MENU”.
If the rinse aid level is set to ZERO, no rinse aid will be supplied. The LOW
RINSE AID indicator light will not be lit if you run out of rinse aid.
A maximum of 6 levels can be set according to the dishwasher model.
• If you see bluish streaks on the dishes, set a low number (0-3).
• If there are drops of water or limescale marks on the dishes, set
a mid-range number (4-5).
on the control
1. Remove the lower rack and unscrew the reservoir cap
(anticlockwise).
2. Position the funnel (see figure) and fill the salt reservoir
right up to its edge (approximately 0,5 kg); it is not un-
usual for a little water to leak out.
FILLING THE DETERGENT DISPENSER
3. Only the first time you do this: fill the salt reservoir
with water.
4. Remove the funnel and wipe any salt residue away
To open the detergent dispenser use the opening device C. Introduce
the detergent into the dry dispenser D only. Place the amount of
detergent for pre-washing directly inside the tub.
1. When measuring out the detergent refer to the
mentioned earlier information to add the proper
quantity. Inside the dispenser D, there are indica-
from the opening.
Make sure the cap is screwed on tightly so that no detergent can get into
the container during the wash program (this could damage the water
softener beyond repair). Run a program every time as soon as you
completed refilling the salt reservoir to avoid corrosion.
D
tions to help the detergent dosing.
2. Remove detergent residues from the edges of the
C
dispenser and close the cover until it clicks.
3. Close the lid of the detergent dispenser by pulling
it up until the closing device is secured in place.
SETTING THE WATER HARDNESS
To allow the water softener to work in a perfect way, it is essential that the water
hardness setting is based on the actual water hardness in your house. This infor-
mation can be obtained from your local water supplier. The factory setting is“3”.
See„WATER HARDNESS TABLE”.
The detergent dispenser automatically opens up at
the right time according to the program.
Usage of detergent not designed for dishwashers may cause
malfunction or damage to the appliance.
Water Hardness Table
°dH
German degrees
°fH
French degrees
°Clark
English degrees
Level
1 (Soft)
2 (Medium)
3 (Average)
4 (Hard)
0 - 6
7 - 11
12 - 16
17 - 34
35 - 50
0 - 10
11 - 20
21 - 29
30 - 60
61 - 90
0 - 7
8 - 14
15 - 20
21 - 42
43 - 62
5 (Very hard)
7
| General | Details |
|---|---|
| Name | Whirlpool WDFS3R4NWESG Sense Dishwasher |
| Make | Whirlpool |
| Language | English |
| Filetype | PDF (Download) |
| File size | 6.06 MB |
(1 votes, average: 5.00 out of 5)
Loading...
Whirlpool 2B19 Dishwasher
Whirlpool WFO3O33PLAUS Standard Dishwasher
Whirlpool W11323304G Dishwasher
Whirlpool WH7IPC15BM60 Dishwasher
Whirlpool FINPUTSAD Dishwasher
Whirlpool W7U HS31 X Dishwasher
Whirlpool Thron Dishwasher
Whirlpool WDF332PAMS 24 Front Tall Tub Dishwasher
Whirlpool WRF540CWHZ Dishwasher
Whirlpool WDF130PAHB Dishwasher
BOSCH SMS6ECC00E Dishwasher
SIEMENS SX75Z802BE Fully Integrated Dishwasher
BOSCH SMI6ZDS16E Dishwasher
Haier HDW15V3S1 Dishwasher
Westinghouse WSF6608KXB Sensor Wash Dishwasher
FISHER PAYKEL DD24DT2NX9 Drawer Dishwasher
Heinner HDW-FS6062WE Dishwasher
FISHER AND PAYKEL DD60ST4HNX9 Contemporary Tall Dishwasher
DAEWOO DA1D5SI0ES Dishwasher
FISHER PAYKEL DD24STX6I1 Sanitize Dishwasher