Whirlpool WFO3O33PLAUS Standard Dishwasher
TROUBLESHOOTING
In case your dishwasher doesn’t work properly, check if the problem can be solved by going through the following list.
For other errors or issues please contact authorized After-sales Service which contact details can be found in the warranty booklet.
The manufacturer ensures the availability of spare parts for at least 10 years after production date of this appliance.
PROBLEMS POSSIBLE CAUSES
SOLUTIONS
Salt
indicator is lit
Salt reservoir is empty (after refill the salt indicator may Refill reservoir with salt (for more information - see page 2).
remain lit for several wash cycles).
Adjust water hardness (see table, page 2).
Rinse aid
indicator is lit
Rinse aid dispenser is empty (after refill the rinse aid
indicator may remain lit for several wash cycles).
Refill dispenser with rinse aid (for more information - see page 2).
Insert the plug into the socket.
The dishwasher
won’t start or does
not respond to
commands.
The appliance has not been plugged in properly.
Power outage.
For safety reasons, dishwasher will not restart automatically when power returns.
Press the START/Pause button to resume the cycle.
The dishwasher door is not closed.
NaturalDry pin is not pulled in.
Vigorously push the door until you hear the “click”.
Cycle is interupted by door opening for > 4 seconds. Close the door and press START/Pause button.
It does not respond to commands. Display shows: Switch off the appliance by pressing the ON/OFF button, switch it back on after
F9 or F12 and both On/Off and START/Pause LEDs approximately one minute and restart the program. If problem persists, unplug the
are blinking rapidly.
appliance for 1 minute, then plug it back in.
The dishwasher
won’t drain.
The wash cycle has not finished yet.
Wait until the wash cycle finishes.
The drain hose is bent.
Check that the drain hose is not bent (see INSTALATION INSTRUCTION).
Clean the sink drain pipe.
Display shows: F3
and both On/Off and
START/Pause LEDs
are blinking rapidly.
The sink drain pipe is blocked.
The filter is clogged up with food residues.
The dishes are rattling against each other.
Clean the filter (see CLEANING THE FILTER ASSEMBLY).
Position the crockery correctly (see LOADING THE RACKS).
The dishwasher
makes
excessive noise.
The detergent has not been measured out correctly or it is not suitable for use in
dishwashers (see FILLING THE DETERGENT DISPENSER). Restart dishwasher by pressing
the DRAIN button (see OPTIONS AND FUNCTIONS) and run new program without
detergent.
An excessive amount of foam has been produced.
The dishes are not
clean.
The crockery has not been arranged properly.
Arrange the crockery correctly (see LOADING THE RACKS).
Arrange the crockery correctly (see LOADING THE RACKS).
Select an appropriate wash cycle (see PROGRAMS TABLE).
The spray arms cannot rotate freely, being hindered
by the dishes.
The wash cycle is too gentle.
The detergent has not been measured out correctly or it is not suitable for use in dish-
washers (see FILLING THE DETERGENT DISPENSER).
An excessive amount of foam has been produced.
The cap on the rinse aid compartment has not been
shut correctly.
Make sure the cap of the rinse aid dispenser is closed.
The filter is soiled or clogged.
There is no salt.
Clean the filter assembly (see CARE AND MAINTENANCE).
Fill the salt reservoir (see FILLING THE SALT RESERVOIR).
The dishwasher does
not fill the water.
Display shows:
and F6, both On/Off
and START/Pause
LEDs are blinking
rapidly.
No water in the water supply or the tap is closed.
The inlet hose is bent.
Make sure there is water in the water supply or the tap running.
Make sure the inlet hose is not bent (see INSTALLATION) reprogram the dishwasher
and reboot.
The sieve in the water inlet hose is clogged; it is
necessary to clean it.
After having carried out the verification and cleaning, turn off and turn on the dish-
washer and restart a new program.
Dishwasher finishes
the cycle prematurely.
Drain hose positioned too low or siphoning into
home sewage system.
Check if end of drain hose is placed at correct height (see INSTALLATION).Check for
siphoning into home sewage system, install air admittance valve if necessary.
Display shows: F15
and both On/Off and
START/Pause LEDs
are blinking rapidly.
Air in water supply.
Check water supply for leaks or other issues letting air inside.
MAINTENANCE AND TROUBLESHOOTING GUIDE
For more information, maintenance procedures and troubleshooting,
see the Use and Care Guide
CONTACTING AFTER-SALES SERVICE
When you contact the After-Sales Service,
you must provide the codes shown on the
rating plate attached to the left or right side
The Use and Care Guide can be obtained by:
•
After-Sales Service; phone number see in warranty inside the door of the dishwasher.
booklet.
download from website: whirlpool.com.au
use QR code
The phone number is listed in the warranty
booklet or on the website:
whirlpool.com.au
•
•
IEC 436
:
400011440913C
09/2020 jk - Xerox Fabriano
8
| General | Details |
|---|---|
| Name | Whirlpool WFO3O33PLAUS Standard Dishwasher |
| Make | Whirlpool |
| Language | English |
| Filetype | PDF (Download) |
| File size | 4.86 MB |
(1 votes, average: 5.00 out of 5)
Loading...
Whirlpool 2B19 Dishwasher
Whirlpool W11323304G Dishwasher
Whirlpool WH7IPC15BM60 Dishwasher
Whirlpool FINPUTSAD Dishwasher
Whirlpool W7U HS31 X Dishwasher
Whirlpool Thron Dishwasher
Whirlpool WDF332PAMS 24 Front Tall Tub Dishwasher
Whirlpool WRF540CWHZ Dishwasher
Whirlpool WDF130PAHB Dishwasher
Whirlpool W11049299A Dishwasher
SAMSUNG DW60H9950FW-SA Dishwasher
IGNIS IG2IE10CS8A0 Fully Dishwasher
FISHER and PAYKEL DD24DTX6I1 Tall Dishwasher
FISHER PAYKEL DD24SCTW9 N Sanitize Dishwasher
VALBERG XAD929C Dishwasher
FISHER AND PAYKEL DW60U4I2 Dishwasher
Electrolux ESA12100SW Dishwasher
SIEMENS SE61HX02AG Dishwasher
Indesit IN2IE10CS80 Dishwasher
beko DUT25401XHW Pocket Handle Dishwasher