caple DI631 Dishwasher
WATER SOFTENER
Contact your local water board for information on the hardness of your water supply.
The water softener must be set manually, using the water hardness dial.
The water softener is designed to remove minerals and salts from the water, which would have a
detrimental or adverse effect on the operation of the appliance.
The higher the content of these minerals and salts, the harder your water is.
The softener should be adjusted according to the hardness of the water in your area. Your local
Water Authority can advise you on the hardness of the water in your area.
WATER SOFTENER
The hardness of the water varies from place to place. If hard water is used in the dishwasher,
deposits will form on the dishes and utensils.
The appliance is equipped with a special softener that uses a salt container specifically designed
to eliminate lime and minerals from the water.
ADJUSTING SALT CONSUMPTION
The dishwasher is designed to allow for adjustment in the amount of salt consumed based on the
hardness of the water used. This is intended to optimise and customise the level of
salt consumption.
LOADING THE SALT INTO THE SOFTENER
Always use salt intended for use with dishwashers.
The salt container is located beneath the lower basket and should be filled as explained in
the following:
Please follow the steps below for adjustment in salt consumption:
1. Open the door and Switch on the appliance.
ATTENTION:
2. Press the Programme button for more than 5 seconds to start the water softener setting within
60 seconds after the appliance was switched on (The Salt and Rinse Aid warning lights will be
on periodically when it is in this setting mode).
»
Only use salt specifically designed for the use in dishwashers. Every other type
of salt not specifically designed for the use in a dishwasher, especially table salt, will damage
the water softener. In case of damages caused by the use of unsuitable salt the manufacturer
does not give any warranty nor is liable for any damages caused.
3. Press the Programme button to select the proper set according to your local environment, the
sets will change in the following sequence: H1->H2->.H3->H4->H5->H6;
»
Only fill with salt just before starting one of the complete washing programmes. This will
prevent any grains of salt or salty water, which may have been spilled, remaining on the
bottom of the machine for any period of time, which may cause corrosion.
4. Press the Power button to end the set up model.
WATER HARDNESS
Selector Position Salt consumption
(gram/cycle)
°DH
°FH
°CLARKE
MMOL/L
1
2
0~5
0~9
0~6
0~0.94
1.0-2.0
2.1-3.0
3.1-4.0
4.1-6.0
6.1-9.8
H1
H2
H3
H4
H5
H6
0
6-11
10-20
21-30
31-40
41-60
61-98
7-14
9
12-17
18-22
23-34
35-55
15-21
22-28
29-42
43-69
12
20
30
60
NOTE: 1
NOTE: 2
The manufactory setting: H3
(EN 50242)
°dH=1.25 °Clarke=1 1.78°fH=0.178mmol/l
°dH: German degree
°fH: French degree
°Clark: British degree
12 Instruction manual DI491 Please keep this instruction manual for future reference
Please keep this instruction manual for future reference Instruction manual DI491
13
| General | Details |
|---|---|
| Name | caple DI631 Dishwasher |
| Make | caple |
| Language | English |
| Filetype | PDF (Download) |
| File size | 2.41 MB |
(1 votes, average: 5.00 out of 5)
Loading...
caple DI654 Dishwasher
caple DI641 Dishwasher
BOSCH SHX5AEM4N 24 Bar Handle Dishwasher
FISHER PAYKEL DD24SCTB9 N Sanitize Dishwasher
FISHER AND PAYKEL DD60DCX9 7 Contemporary Dishwasher
SAMSUNG DW80BB70 Series Dishwasher
BOSCH SRV2HKX39G Fully- Dishwasher
BOSCH 041203 Dishwasher
Electrolux EEC67310L Comfortlift Airdry Total Dishwasher
Whirlpool WIE 2B19 N Dishwasher
RESPEKTA GSP60IBATIDM Dishwasher
FISHER PAYKEL DD24STI9N Sanitize Dishwasher