Home > caple > caple DI631 Dishwasher

caple DI631 Dishwasher

NOTE: EN 50242:  
This programme is the test cycle. The information for comparability test in accordance with EN  
50242, as follows:  
FORGOT TO ADD A DISH  
A forgotten dish can be added any time before the detergent cap opens:  
»
»
»
»
»
Open the door a little.  
»
»
»
»
Capacity: 12 settings  
After the spray arms stop working, you can open the door completely  
Add forgotten dishes  
Position Upper basket: upper wheels on rails  
Rinse Aid setting: 6  
Close the door  
PI:0.49w;Po:0.45w  
The dishwasher will start running again  
TURNING ON THE APPLIANCE  
Starting a wash cycle:  
AT THE END OF THE WASH CYCLE  
When the working cycle has finished, the buzzer of the dishwasher will sound for 8 seconds, then  
stop. Turn off the appliance using the ON/OFF button, shut off the water supply (if connected to  
tap only) and open the door of the dishwasher.  
»
Pull out the lower and upper baskets, load the dishes and push them back. It is recommended  
to load the lower basket first, then the upper one (see the section entitled “Loading  
the Dishwasher”).  
Wait for a few minutes before unloading the dishwasher to avoid handling the dishes and utensils  
while they are still hot and more susceptible to breakage. They will also dry better.  
»
»
Pour in the detergent (see the section entitled Salt, Detergent and Rinse Aid).  
Insert the plug into the socket. The power supply is 220-240 VAC /50 HZ, the specification of  
the socket is 10A 250VAC. Make sure that the water supply is turned on to full pressure.  
SWITCH OFF THE DISHWASHER  
The programme light is on but is not blinking, only in this case the programme  
has ended.  
1.Open the door. Switch off the dishwasher by pressing the ON/OFF button.  
2.Turn off the water tap (if not plumbed into mains water supply).  
»
»
Open the door, press the power button, and the On/Off light will turn on.  
Press the program Button , the wash program will be changed as follows direction:  
Intensive->Normal->ECO->90Min->Rapid;  
CHANGE THE PROGRAMME  
OPEN THE DOOR CAREFULLY  
Hot dishes are sensitive to knocks. The dishes should therefore be allowed to cool down around 15  
minutes before removing from the appliance.  
Open the dishwasher’s door, leave it ajar and wait a few minutes before removing the dishes. In  
this way they will be cooler and the drying will be improved.  
»
»
A cycle that is underway can only be modified if it has only been running for a short time.  
Otherwise, the detergent may have already been released, and the appliance may have already  
drained the wash water. If this is the case, the detergent dispenser must be refilled (see the  
section entitled “Loading the Detergent“).  
Open the door, press the Programme button for 3 seconds, the machine will be in standby  
state, then you can change the programme to the desired cycle setting (see the section entitled  
“Starting a wash cycle”).  
UNLOADING THE DISHWASHER  
It is normal that the dishwasher is wet inside.  
Empty the lower basket first and then the upper one. This will avoid water dripping from the upper  
Basket onto the dishes in the lower one.  
NOTE:  
If you open the door during a wash cycle, the machine will pause. The programme light will stop  
blinking and the buzzer will sound every minute until you close the door. After you close the door,  
the machine will continue working again.  
WARNING:  
It is dangerous to open the door during a wash cycle, because the hot water or steam may  
scald you.  
26 Instruction manual DI631 Please keep this instruction manual for future reference  
Please keep this instruction manual for future reference Instruction manual DI631  
27  
GeneralDetails
Namecaple DI631 Dishwasher
Makecaple
LanguageEnglish
FiletypePDF (Download)
File size2.41 MB
Download PDF
1 Star2 Stars3 Stars4 Stars5 Stars (1 votes, average: 5.00 out of 5)
Loading...
caple DI654 Dishwasher
caple DI654 Dishwasher
caple DI641 Dishwasher
caple DI641 Dishwasher

caple DI631 Dishwasher