GAGGENAU DF480701F Dishwasher
en-usꢀDishwasher Connection
3. Mark the correct position, then slide the brackets out
some detergents to lose effectiveness. Lower water
temperatures will increase run times. The hot water supply
pressure must be between 7.25 - 145 psi (0.5 - 10 bar).
and bend out the metal tab at the correct position.
WARNING
Scalding Hazard
▶ Do not perform any work on a pressured hot water line.
Serious injury could result. Only qualified plumbers
should perform plumbing work. Do not attempt any work
on the dishwasher hot water supply plumbing until you
are certain the hot water supply is shut off.
NOTICE:
Soldering plumbing lines
▶ Temperatures required for soldering and sweating will
damage the dishwasher. If plumbing lines are to be
soldered or sweated, keep the heat source at least 6
inches (152.4 mm) away from the dishwasher.
Plumbing codes
▶ Check local plumbing codes for approved plumbing
procedures and accessories. All plumbing should be
done in accordance with national and local codes.
Bending a tab ensures that the toe panel cannot slide in
further.
4. Re-insert the brackets.
5. Secure the outer toe panel with the crosshead screws
provided.
Note
‒ The outer toe panel should completely cover the
rubber apron.
6. To cover the screw heads, use the black plastic caps.
Important notes for water connection:
¡ If using a solder joint instead of a compression fitting,
be sure to complete all solder connections before
connecting the water supply line to the dishwasher.
¡ Use an approved dishwasher water supply line with the
correct fittings for this connection.
¡ If using copper tubing or other material not depicted in
this manual for water supply, defer to a licensed
plumber for proper installation.
¡ Always use appropriate seals when making plumbing
connections.
1. Flush the incoming water line for approximately 1
minute to clear any foreign material.
2. Connect the dishwasher water supply line to the water
shut off valve, using the adaptor if included with your
model.
‒ Install a shut off valve if one isn’t already in the
supply line.
‒ Make sure there are no sharp bends or kinks in the
water line that might restrict water flow.
D
h
e
5ꢀDishwasher Connection
D
h
Follow these instructions to connect the dishwasher.
5.1ꢀInstalling the Water Inlet Connection
The hot water heater should be set to deliver
approximately 120 °F (49 °C) [max. 140 °F/ (60 °C)]
water to the dishwasher. Water that is too hot can cause
16
| General | Details |
|---|---|
| Name | GAGGENAU DF480701F Dishwasher |
| Make | Gaggenau |
| Language | English |
| Filetype | PDF (Download) |
| File size | 1.51 MB |
(1 votes, average: 5.00 out of 5)
Loading...
Gaggenau DF264101 Dishwasher
GAGGENAU DF271101F Dishwasher
GAGGENAU DF481100 Dishwasher
GAGGENAU 400 Dishwasher
GAGGENAU DF480161F Dishwasher
Gaggenau 9001923384 B Dishwasher
GAGGENAU DF261101 Dishwasher
Gaggenau DF211700 Dishwasher
GAGGENAU DF481100F 400 Series Dishwasher
GAGGENAU 11029813 Fully- Dishwasher
FISHER and PAYKEL DD60D4HNX9 Contemporary Dishwasher
LG XD3A25UNS Dishwasher
FISHER PAYKEL DD60SDFTB9 Dishwasher
SIEMENS SN63HX42VE Dishwasher
BOSCH 300 Series Recessed Handle Dishwasher
FISHER PAYKEL DD24DCTB9N Dishwasher
SIEMENS SN23EI00ME Dishwasher
BOSCH SHP865ZD5N Pocket Handle Dishwasher
FISHER and PAYKEL DD60STX6HI1 Dishwasher
BERTAZZONI DW24S2IPB Dishwasher