Home > Ikea > IKEA RÅGLANDA Dishwasher

IKEA RÅGLANDA Dishwasher

ENGLISH  
17  
Installation  
ATTENTION: If the appliance must be moved at any time, keep  
it in an upright position; if absolutely necessary, it may be tilted  
onto its back.  
Electrical connection  
WARNING: Under no circumstances should the water inlet  
hose be cut as it contains live electrical parts.  
Before inserting the plug into the electrical socket, make sure  
that:  
• The socket is earth and complies with current regulations;  
• The socket can withstand the maximum load of the  
appliance as shown on the data plate located on the inside of  
the door (see PRODUCT DESCRIPTION).  
• The power supply voltage falls within the values indicated on  
the data plate on the inside of the door.  
• The socket is compatible with the plug of the appliance.  
If this is not the case, ask an authorised service only to replace  
the certified power cord with a correct plug dedicated for this  
appliance (see AFTER-SALES SERVICE). Do not use extension cab-  
lesor multiple sockets or not authorized power cords with plugs.  
Once the appliance has been installed, the power supply cable  
and the electrical socket should be easily accessible.  
The cable should not be bent or compressed.  
If the power supply cable is damaged, have it replaced by the  
manufacturer or its authorised Technical Assistance Service in  
order to prevent all potential hazards.  
Connecting the water supply  
Adaptation of the water supply for installation should only be  
performed by a qualified technician.  
The water inlet and outlet hoses may be positioned towards the  
right or the left in order to achieve the best possible installation.  
Make sure the dishwasher does not bend or squash the hoses.  
Connecting the water inlet hose  
• Run the water until it is perfectly clear.  
• Screw the inlet hose tightly into position and turn on the tap.  
If the inlet hose is not long enough, contact a specialist store or  
an authorised technician.  
The water pressure must be within the values indicated in the  
Technical Data table - otherwise the dishwasher may be function  
properly.  
Make sure the hose is not bent or compressed.  
Specifications for the connection of the water supply hose:  
Water supply  
Water intake  
cold or hot (max. 60°C)  
The Company shall not be held responsible for any incidents, if  
these regulations are not observed.  
3/4”  
0.05 ÷ 1 MPa (0.5 ÷ 10 bar)  
7.25 – 145 psi  
Positioning and levelling  
Power of water pressure  
1. Position the dishwasher on a level sturdy floor. If the floor is  
uneven, the front feet of the appliance may be adjusted until  
it reaches a horizontal position. If the appliance is levelled  
correctly, it will be more stable and much less likely to move  
or cause vibrations and noise while it is operating.  
Connecting the water outlet hose  
Connect the outlet hose to a drain duct with a minimum  
diameter of 2 cm A.  
2. Before recessing the dishwasher, stick the adhesive transparent  
strip under the wooden shelf in order to protect it from any  
condensation which may form.  
MAX 80 cm  
3. Place the dishwasher so that its sides or back panel are in  
contact with the adjacent cabinets or the wall. This appliance  
can also be recessed under a single worktop.  
MIN 40 cm  
4. To adjust the height of the rear foot, turn the red hexagonal  
bushing on the lower central part at the front of the  
dishwasher using a hexagonal spanner with an opening of 8  
mm. Turn the spanner in a clockwise direction to increase the  
height and in an anticlockwise direction to decrease it.  
The outlet hose connection must be at a height ranging from  
40 to 80 cm from the floor or surface where the dishwasher  
rests.  
Before connecting the water outlet hose to the sink drain,  
remove the plastic plug B.  
DIMENSIONS AND CAPACITY:  
Width  
598 mm  
ANTI-FLOODING PROTECTION  
Height  
Depth  
820 mm  
Anti-flooding protection. To ensure floods do not occur, the  
dishwasher is provided with a special system which blocks the  
water supply in the event of anomalies or leaks from inside the  
appliance.  
555 mm  
Capacity  
14 standard place-settings  
The dishwasher is also equipped with the supplementary  
safety device New Aqua Stop, which guarantees anti-flooding  
protection even in the event of a supply hose rupture.  
Under no circumstances should the water inlet hose be cut as it  
contains live electrical parts.  
GeneralDetails
NameIKEA RÅGLANDA Dishwasher
MakeIkea
LanguageEnglish
FiletypePDF (Download)
File size59.62 MB
Download PDF
1 Star2 Stars3 Stars4 Stars5 Stars (1 votes, average: 5.00 out of 5)
Loading...
IKEA 404.755.53 Medelstor Dishwasher
IKEA 404.755.53 Medelstor Dishwasher
IKEA 804.621.67 Lagan Dishwasher
IKEA 804.621.67 Lagan Dishwasher
IKEA RENGÖRA 204.756.05 Dishwasher
IKEA RENGÖRA 204.756.05 Dishwasher
IKEA 9001774317 TORSBODA Dishwasher
IKEA 9001774317 TORSBODA Dishwasher
IKEA 9001774318 Dishwasher
IKEA 9001774318 Dishwasher
IKEA SBE8596Z0E DISKAD PROFFSIG Dishwasher
IKEA SBE8596Z0E DISKAD PROFFSIG Dishwasher
IKEA VILLBODA Dishwasher
IKEA VILLBODA Dishwasher
IKEA 504.754.25 HYGIENISK Dishwasher
IKEA 504.754.25 HYGIENISK Dishwasher
IKEA AA-2412057-2-1 RÅGLANDA Dishwasher
IKEA AA-2412057-2-1 RÅGLANDA Dishwasher
IKEA 905.681.49 OSTVEDA Dishwasher
IKEA 905.681.49 OSTVEDA Dishwasher

IKEA RÅGLANDA Dishwasher