InDeSIT IN2FE10CS90S Dishwasher
FIRST TIME USE
SALT, RINSE AID AND DETERGENT
ADVICE REGARDING THE FIRST TIME USE
FILLING THE RINSE AID DISPENSER
After installation, remove the stoppers from the racks and the retaining Rinse aid makes dish DRYING easier. The rinse aid dispenser A should
be filled when when the dark optical indicator on the dispenser door C
becomes transparent.
elastic elements from the upper rack.
FILLING THE SALT RESERVOIR
C
The use of salt prevents the formation of LIMESCALE on the dishes and
on the machine’s functional components.
•
•
It is mandatory that THE SALT RESERVOIR NEVER BE EMPTY.
It is important to set the water hardness.
The salt reservoir is located in the lower part of the dishwasher (see
PRODUCT DESCRIPTION) and must be filled when the green float on the
cap of the salt reservoir is no longer visible.
B
A
1. Remove the lower rack and unscrew the
reservoir cap (anticlockwise).
2. Only the first time you do this: fill the salt
reservoir with water.
3. Position the funnel (see figure) and fill the salt
reservoir right up to its edge (approximately
1 kg); it is not unusual for a little water to leak
out.
4. Remove the funnel and wipe any salt residue
away from the opening.
1. Open the dispenser B by pressing and pulling up the tab on the lid.
2. Pour in the rinse aid (max.110 ml), making sure it does not overflow
from the dispenser. If this happens, clean the spill immediately with
a dry cloth.
3. Press the lid down until you hear a click to close it.
NEVER pour the rinse aid directly into the appliance tub.
ADJUSTING THE DOSAGE OF RINSE AID
If you are not completely satisfied with the drying results, you can ad-
just the quantity of rinse aid used.
Make sure the cap is screwed on tightly, so that no detergent can get
into the container during the wash program (this could damage the
water softener beyond repair).
Whenever you need to add salt, it is mandatory to complete the pro-
cedure before the beginning of the washing cycle to avoid corrosion.
• Switch the dishwasher on using the ON/OFF button.
• Switch it off using the ON/OFF button.
• Press button START/Pause three times.
• Switch it on using the ON/OFF button.
• The START LED light will flash as many times as the level that was set.
SETTING THE WATER HARDNESS
To allow the water softener to work in a perfect way, it is essential that
the water hardness setting is based on the actual water hardness in
your house. This information can be obtained from your local water
supplier.
• Set the level of rinse aid quantity to be supplied using the PROGRAM
SELECTION knob (see PROGRAMS TABLE).
• Switch it off using the ON/OFF button
Setting is complete!
The factory sets the default value for the water hardness:
If the rinse aid level is set to 1 (ECO), no rinse aid will be supplied.
• Switch on the appliance by pressing the ON/OFF button.
• Switch off the appliance by pressing the ON/OFF button.
• Hold down button START/Pause for 5 seconds.
A maximum of 5 levels can be set according to the dishwasher model.
The factory setting is specific to the model, please follow instruction
above to check this for your machine
• Switch on the appliance by pressing the ON/OFF button.
• The ON/OFF LED light will flash as many times as the level that was set.
• If you see bluish streaks on the dishes, set a low number (2-3).
• If there are drops of water or limescale marks on the dishes, set a mid-
range number (4-5).
• Set the desired water hardness level using the PROGRAM SELECTION
knob (see WATER HARDNESS TABLE).
FILLING THE DETERGENT DISPENSER
Water Hardness Table
To open the detergent dispenser use the opening device D.
Introduce the detergent into the dry dispenser E only. Place the
amount of detergent for pre-washing directly inside the tub.
°dH
German degrees French degrees English degrees
°fH
°Clark
Level
Soft
1
2
3
4
5
0 - 6
0 - 10
11 - 20
21 - 29
30 - 60
61 - 90
0 - 7
1. When measuring out the detergent
refer to the mentioned earlier infor-
mation to add the proper quantity.
Medium
Average
Hard
7 - 11
8 - 14
12 - 16
17 - 34
35 - 50
15 - 20
21 - 42
43 - 62
Inside the dispenser E there are indi-
cations to help the detergent dosing.
E
2. Remove detergent residues from
the edges of the dispenser and
close the cover until it clicks.
D
Very hard
• Switch off the appliance by pressing the ON/OFF button.
3. Close the lid of the detergent dis-
penser by pulling it up until the
closing device is secured in place.
Setting is complete!
As soon as this procedure is complete, run a program without loading.
Only use salt that has been specifically designed for dishwashers.
If the salt container is not filled, the water softener and the heating
element may be damaged as a result of limescale accumulation.
Using of Salt is recommended with any type of dishwasher deter-
gent.
The detergent dispenser automatically opens up at the right time
according to the program.
Usage of detergent not designed for dishwashers may cause mal-
function or damage to the appliance.
2
| General | Details |
|---|---|
| Name | InDeSIT IN2FE10CS90S Dishwasher |
| Make | INDESIT |
| Language | English |
| Filetype | PDF (Download) |
| File size | 9.14 MB |
(1 votes, average: 5.00 out of 5)
Loading...
INDESIT D2I HL326 Full Size Dishwasher
Indesit D2F HD624 A Separate Dishwasher
Indesit 869991713220 Dishwasher
INDESIT I0F D641A X Free Standing Dishwasher
Indesit I0F D641A Dishwasher
INDESIT DFE 1B19 14 Dishwasher
INDeSIT D2F Dishwasher
INDeSIT D2I HD524 A Dishwasher
INDESIT W11667630 B Dishwasher
inDeSIT DSIO3M24CS Dishwasher
BOSCH SMS4HMB62T Free Standing Dishwasher
smeg LSPU8612S Silver Dishwasher
Miele G 5058 SCVi SFP Dishwasher
MONOGRAM ZDT985SINII Dishwasher
FISHER PAYKEL DD60D2HNB9 Built Under Double Dishwasher
BOSCH SMS2HKI03E-30 Dishwasher
Whirlpool W11389327B Dishwasher
FISHER PAYKEL DD60DDFX9 Double Sanitise DishDrawer Dishwasher
beko DUT25401WHW Front Pocket Handle Dishwasher
FISHER PAYKEL DD24SAX9N Single DishDrawer Dishwasher