Thermador DWHD640EFM Dishwasher
en-usꢀDishwasher Connection
D
h
2. Connect the dishwasher water supply line to the water
shut off valve, using the adaptor if included with your
model. Turn by hand and do not over tighten.
5ꢀDishwasher Connection
Follow these instructions to connect the dishwasher.
D
h
‒ Install a shut off valve if one isn’t already in the
supply line.
‒ Make sure there are no sharp bends or kinks in the
water line that might restrict water flow.
5.1ꢀInstalling the Water Inlet Connection
The hot water heater should be set to deliver
approximately 120 °F (49 °C) [max. 140 °F/ (60 °C)]
water to the dishwasher. Water that is too hot can cause
some detergents to lose effectiveness. Lower water
temperatures will increase run times. The hot water supply
pressure must be between 7.25 - 145 psi (0.5 - 10 bar).
WARNING
Scalding Hazard
▶ Do not perform any work on a pressured hot water line.
Serious injury could result. Only qualified plumbers
should perform plumbing work. Do not attempt any work
on the dishwasher hot water supply plumbing until you
are certain the hot water supply is shut off.
NOTICE:
Soldering plumbing lines
▶ Temperatures required for soldering and sweating will
damage the dishwasher. If plumbing lines are to be
soldered or sweated, keep the heat source at least 6
inches (152.4 mm) away from the dishwasher.
Plumbing codes
3. After all connections are made, turn on the hot water
and check for leaks.
5.2ꢀInstalling the Drain Connection
▶ Check local plumbing codes for approved plumbing
procedures and accessories. All plumbing should be
done in accordance with national and local codes.
The drain hose must be installed with either a high loop or
an air gap.
NOTICE:
Proper drain hose installation
Note
Important notes for water connection:
▶ The dishwasher drain hose must be installed with a
portion of it at least 33” (84 cm) off the floor; otherwise
the dishwasher may not drain properly.
Remove garbage disposal plug
▶ If the dishwasher drain hose will be connected to a
garbage disposal connection, first remove the plug from
the disposal connection.
¡ If using a solder joint instead of a compression fitting,
be sure to complete all solder connections before
connecting the water supply line to the dishwasher.
¡ Use an approved dishwasher water supply line with the
correct fittings for this connection.
¡ If using copper tubing or other material not depicted in
this manual for water supply, defer to a licensed
plumber for proper installation.
Note
¡ Always use appropriate seals when making plumbing
connections.
Important notes for drain connection:
¡ If local ordinance require an air gap, install it according
to the manufacturer’s instructions.
¡ The drain hose length can be extended if necessary.
Use kit #SGZ1010UC. The maximum length of the drain
hose, including the hose leading to the air gap, is 150″
(380 cm).
1. Flush the incoming water line for approximately 1
minute to clear any foreign material.
¡ You may attach the hose clip to the inside of the
adjacent cabinet to hang the drain hose (screws are not
supplied) in place of using a nonmetallic tie as pictured
in the next illustrations. Do not exceed 43” in drain hose
height.
14
| General | Details |
|---|---|
| Name | Thermador DWHD640EFM Dishwasher |
| Make | Thermador |
| Language | English |
| Filetype | PDF (Download) |
| File size | 4.05 MB |
(1 votes, average: 5.00 out of 5)
Loading...
Thermador DWHD660EFP Sapphire Dishwasher
Thermador DWHD660EFM Dishwasher
Thermador DWHD640EFP Dishwasher
Thermador Dishwasher : for DWHD650W and More
AEG FSK52617Z Dishwasher
FISHER PAYKEL DD24SI9 N Integrated Single Dishwasher
FISHER PAYKEL DW60UC6B Built Under Dishwasher
Smeg DI362DQ Dishwasher
BOSCH SPV4HKX53E 4 Total Dishwasher
BOSCH SMV6ZCX17E Dishwasher
FISHER AND PAYKEL DD24SAX9 N Dishwasher
FISHER PAYKEL DD60DDFHX9 Dishwasher
AIRMSEN AE-TDQR03 Complete Dishwasher
BOSCH SMD8YC801E Dishwasher