Hotpoint HFC 3C26 WCUK Dishwasher
EN
CARE AND MAINTENANCE
CLEANING THE FILTER ASSEMBLY
CLEANING THE SPRAY ARMS
Regularly clean the filter assembly so that the filters do not clog and On occasions, food residue may become encrusted onto the spray arms
that the waste water flows away correctly.
and block the holes used to spray the water. It is therefore recommen-
ded that you check the arms from time to time and clean them with
a small non-metallic brush.
Using dishwasher with clogged filters or foreign objects inside filtration
system or sprayarms may cause unit malfunction resulting in lose of
performance, noisy work or higher resources usage.
The filter assembly consists of three filters which remove food residues
from the washing water and then recirculate the water.
The dishwasher must not be used without filters or if the filter is lo-
ose.
At least once per month or after each 30 cycles, check the filter assembly
and if necessary clean it thoroughly under running water, using a non-
-metallic brush and following the instructions below:
1. Turn the cylindrical filter A in an anti-clockwise direction and pull it
out (Fig 1).
To remove the upper spray arm, turn the plastic locking ring in a cloc-
kwise direction. The upper spray arm should be replaced so that the
side with the greater number of holes is facing upwards.
2. Remove the cup filter B by exerting a slight pressure on the side
flaps (Fig 2).
3. Slide out the stainless-steel plate filter C (Fig 3).
4. In case you find foreign objects (such as broken glass, porcelain,
bones, fruit seeds etc.) please remove them carefully.
5. Inspect the trap and remove any food residues. NEVER REMOVE the
wash-cycle pump protection (black detail) (Fig 4).
1
2
The lower spray arm may be removed by pulling it upwards.
B
A
A
WATER SOFTENING SYSTEM
Water softener automatically reduces water hardness, consequently
preventing scale buildup on heater, contributing also to better cleaning
efficiency.
This system regenerates itself with salt, therefore it is required to
refill salt container when empty.
Frequency of regeneration depends on water hardness level setting -
regeneration takes place once per 6 Eco cycles with water hardness
level set to 3.
Regeneration process starts in final rinse and finishes in drying phase,
before cycle ends.
C
3
4
•
•
•
Single regeneration consumes: ~3.5L of water;
Takes up to 5 additional minutes for the cycle;
Consumes below 0.005kWh of energy.
After cleaning the filters, re-place the filter assembly and fix it in
position correctly; this is essential for maintaining the efficient
operation of the dishwasher.
CLEANING THE WATER INLET HOSE
If the water hoses are new or have not been used for an extended
period of time, let the water run to make sure it is clear and free
of impurities before performing the necessary connections. If this
precaution is not taken, the water inlet could become blocked and da-
mage the dishwasher.
7
| General | Details |
|---|---|
| Name | Hotpoint HFC 3C26 WCUK Dishwasher |
| Make | Hotpoint |
| Language | English |
| Filetype | PDF (Download) |
| File size | 31.12 MB |
(1 votes, average: 5.00 out of 5)
Loading...
Hotpoint H7I HP42 L UK Dishwasher
Hotpoint H7F HP33 UK Dishwasher
Hotpoint H7F HS41 UK Full Size Dishwasher
Hotpoint H8I HT59 LS UK Dishwasher
Hotpoint H7F HS51 Dishwasher
Hotpoint H7FHS41 Dishwasher
Hotpoint HA3FC10BS7A0S Dishwasher
Hotpoint H7F HS41 X Dishwasher
Hotpoint 869991662940 Dishwasher
Hotpoint H7I HT59 L Dishwasher
BOSCH SMV4ECX21E-38 Dishwasher
FISHER PAYKEL DW60U4I2 Sanitise Integrated Dishwasher
BOSCH SMV6ZCX10G Dishwasher
Electrolux EET43200LX Fully Integrated Dishwasher
Home Connect SMS4HVW00E Dishwasher
BOSCH SMI4EAS23E Dishwasher
BOSCH S187ZCX03G Fully Dishwasher
INVENTUM VVW6030AS dishwasher
MEIKO UPster U 400 M2 Glass and Dishwasher
GE Appliances GSC470 Dishwasher