Hotpoint HSFC 3T127 C Dishwasher
TROUBLESHOOTING
In case your dishwasher doesn’t work properly, check if the problem can be solved by going through the following list.
For other errors or issues please contact authorized After-sales Service which contact details can be found in the warranty booklet.
Spare parts will be available for a period of either up to 7 or up to 10 years, according to the specific Regulation requirements.
PROBLEMS POSSIBLE CAUSES
SOLUTIONS
Salt reservoir is empty (after refill the salt indicator may Refill reservoir with salt (for more information - see page 2).
Salt
indicator is lit
remain lit for several wash cycles).
Adjust water hardness (see table, page 2).
Rinse aid dispenser is empty (after refill the rinse aid
indicator may remain lit for several wash cycles).
Rinse aid
indicator is lit
Refill dispenser with rinse aid (for more information - see page 2).
The dishwasher
won’t start or does
not respond to
commands.
The appliance has not been plugged in properly.
Power outage.
Insert the plug into the socket.
For safety reasons, dishwasher will not restart automatically when power returns.
Press the START/Pause button to resume the cycle.
The dishwasher door is not closed.
Vigorously push the door until you hear the “click”.
Close the door and press START/Pause.
Cycle is interupted by door opening for > 4 sec.
It does not respond to commands.
Display shows: F9 or F12 and both On/Off and
START/Pause LEDs are blinking rapidly.
Switch off the appliance by pressing the ON/OFF button, switch it back on after
approximately one minute and restart the program. If problem persists, unplug the
appliance for 1 minute, then plug it back in.
The dishwasher
won’t drain.
Display shows: F3
and both On/Off and
START/Pause LEDs
are blinking rapidly.
The wash cycle has not finished yet.
The drain hose is bent.
Wait until the wash cycle finishes.
Check that the drain hose is not bent (see INSTALATION INSTRUCTION).
Clean the sink drain pipe.
The sink drain pipe is blocked.
The filter is clogged up with food residues.
The dishes are rattling against each other.
Clean the filter (see CLEANING THE FILTER ASSEMBLY).
Position the crockery correctly (see LOADING THE RACKS).
The dishwasher
makes
excessive noise.
The detergent has not been measured out correctly or it is not suitable for use in
dishwashers (see FILLING THE DETERGENT DISPENSER). Restart dishwasher by pressing
the DRAIN button (see OPTIONS AND FUNCTIONS) and run new program without
detergent.
An excessive amount of foam has been produced.
The dishes are not
clean.
The crockery has not been arranged properly.
Arrange the crockery correctly (see LOADING THE RACKS).
Arrange the crockery correctly (see LOADING THE RACKS).
Select an appropriate wash cycle (see PROGRAMS TABLE).
The spray arms cannot rotate freely, being hindered
by the dishes.
The wash cycle is too gentle.
The detergent has not been measured out correctly or it is not suitable for use in
dishwashers (see FILLING THE DETERGENT DISPENSER).
An excessive amount of foam has been produced.
The cap on the rinse aid compartment has not been
shut correctly.
Make sure the cap of the rinse aid dispenser is closed.
The filter is soiled or clogged.
There is no salt.
Clean the filter assembly (see CARE AND MAINTENANCE).
Fill the salt reservoir (see FILLING THE SALT RESERVOIR).
Make sure there is water in the water supply or the tap running.
The dishwasher does
not fill the
No water in the water supply or the tap is closed.
water. Display shows:
and F6, both On/
Off and START/Pause
LEDs are blinking
rapidly.
Make sure the inlet hose is not bent (see INSTALLATION) reprogram the dishwasher
and reboot.
The inlet hose is bent.
The sieve in the water inlet hose is clogged; it is
necessary to clean it.
After having carried out the verification and cleaning, turn off and turn on the
dishwasher and restart a new program.
Dishwasher finishes
the cycle prematurely.
Display shows: F15
and both On/Off and
START/Pause LEDs
are blinking rapidly.
Drain hose positioned too low or siphoning into
home sewage system.
Check if end of drain hose is placed at correct height (see INSTALLATION).Check for
siphoning into home sewage system, install air admittance valve if necessary.
Air in water supply.
Check water supply for leaks or other issues letting air inside.
Depends on the liquid detergent used and can be
emphasized in case of delay option is activated.
Small leaks will not cause machine malfunction and can be avoided by changing
liquid detergent type or using tablets.
Detergent leaks.
Policies, standard documentation, ordering of spare parts and additional product information can be found by:
•
•
•
Using QR code on your product.
Visiting our website docs.hotpoint.eu and parts-selfservice.europeanappliances.com
Alternatively, contact our After-sales Service (See phone number in the warranty booklet). When contacting our
After-sales Service, please state the codes provided on your product‘s identification plate.
The model information can be retrieved using the QR-Code reported in the energy label. The label also includes
IEC 436
:
8
| General | Details |
|---|---|
| Name | Hotpoint HSFC 3T127 C Dishwasher |
| Make | Hotpoint |
| Language | English |
| Filetype | PDF (Download) |
| File size | 18.07 MB |
(1 votes, average: 5.00 out of 5)
Loading...
Hotpoint H7I HP42 L UK Dishwasher
Hotpoint H7F HP33 UK Dishwasher
Hotpoint H7F HS41 UK Full Size Dishwasher
Hotpoint H8I HT59 LS UK Dishwasher
Hotpoint H7F HS51 Dishwasher
Hotpoint H7FHS41 Dishwasher
Hotpoint HA3FC10BS7A0S Dishwasher
Hotpoint H7F HS41 X Dishwasher
Hotpoint 869991662940 Dishwasher
Hotpoint H7I HT59 L Dishwasher
FISHER and PAYKEL DD60DI9 Integrated Dishwasher
Mueller DW-2400 Dishwasher
NEFF S395HCX26G Dishwasher
GRUNDIG GNFP3440X Dishwasher
BOSCH SBH4HB802E-46 Dishwasher
FISHER PAYKEL DD60D2NB9 Built Under Dishwasher
Miele PFD 402 Fresh Water Dishwasher
FISHER & PAYKEL DW60UNT4X2 Built-Under Dishwasher
FISHER and PAYKEL DW24UT2I2 Series 7 Integrated Dishwasher
BOSCH SMD8YCX02G Dishwasher