INDESIT D2I HL326 Full Size Integrated Dishwasher
EN
TROUBLESHOOTING
In case your dishwasher doesn’t work properly, check if the problem can be solved by going through the following list.
For other errors or issues please contact authorized After-sales Service which contact details can be found in the warranty booklet.
Spare parts will be available for a period of either up to 7 or up to 10 years, according to the specific Regulation requirements.
PROBLEMS POSSIBLE CAUSES
Salt reservoir is empty.
Salt indicator
SOLUTIONS
Refill reservoir with salt (for more information - see page 2).
Adjust water hardness - see table, page 2.
(After refill the salt indicator may remain lit
for several wash cycles).
is lit
The appliance has not been plugged in
properly.
The dishwasher
won’t start
Insert the plug into the socket.
or does not
respond to com-
mands.
For safety reasons, dishwasher will not re-start automatically when power returns.
Open dishwasher door, press Start button and close the door within 4 seconds.
Power outage.
The dishwasher door is not closed.
Vigorously push the door until you hear the “click”.
Cycle is interupted by door opening for
more than 4 seconds.
Press START/Pause and close the door within 4 seconds.
Switch off the appliance by pressing the ON/OFF button, switch it back on
after approximately one minute and restart the program. If problem persists,
unplug the appliance for 1 minute, then plug it back in.
It does not respond to commands.
The wash cycle has not finished yet.
The drain hose is bent.
Wait until the wash cycle finishes.
The dishwasher
won’t drain.
Check that the drain hose is not bent (see INSTALATION INSTRUCTION).
Clean the sink drain pipe.
The sink drain pipe is blocked.
The filter is clogged up with food residues. Clean the filter (see CLEANING THE FILTER ASSEMBLY).
The dishes are rattling against each other. Position the crockery correctly (see LOADING THE RACKS).
The detergent has not been measured out correctly or it is not suitable for
The dishwasher
makes
excessive noise.
use in dishwashers (see FILLING THE DETERGENT DISPENSER). Restart the cur-
rent cycle by switching OFF the dishwasher, then switch it on again, select a
produced.
An excessive amount of foam has been
new program, press START/Pause and close the door within 4 seconds. Please
do not add any detergent.
The crockery has not been arranged
Arrange the crockery correctly (see LOADING THE RACKS).
properly.
The dishes are
not clean.
The spray arms cannot rotate freely, being
Arrange the crockery correctly (see LOADING THE RACKS).
hindered by the dishes.
The wash cycle is too gentle.
Select an appropriate wash cycle (see PROGRAMS TABLE).
An excessive amount of foam has been
produced.
The detergent has not been measured out correctly or it is not suitable for use
in dishwashers (see FILLING THE DETERGENT DISPENSER).
The cap on the rinse aid compartment has
not been shut correctly.
Make sure the cap of the rinse aid dispenser is closed.
The filter is soiled or clogged.
There is no salt.
Clean the filter assembly (see CARE AND MAINTENANCE).
Fill the salt reservoir (see FILLING THE SALT RESERVOIR).
No water in the water supply or the tap is
closed.
The dishwasher
does not fill the
water.
Make sure there is water in the water supply or the tap running.
Make sure the inlet hose is not bent (see INSTALLATION) reprogram the dish-
washer and reboot.
The inlet hose is bent.
All LEDs are
blinking rapidly
The sieve in the water inlet hose is clogged; After having carried out the verification and cleaning, turn off and turn on the
it is necessary to clean it
dishwasher and restart a new program.
Check if end of drain hose is placed at correct height (see INSTALLATION).
Check for siphoning into home sewage system, install air admittance valve if
necessary.
Dishwasher
finishes the cycle
prematurely.
Drain hose positioned too low or siphoning
into home sewage system.
Air in water supply.
Check water supply for leaks or other issues letting air inside.
Policies, standard documentation, ordering of spare parts and additional product
information can be found by:
•
•
•
Visiting our website docs.indesit.eu and parts-selfservice.whirlpool.com
Using QR Code
Alternatively, contact our After-sales Service (See phone number in the warranty booklet).
When contacting our After-sales Service, please state the codes provided on your product‘s
identification plate.
IEC 436
:
The model information can be retrieved using the QR-Code reported in the energy label.
The label also includes the model identifier that can be used to consult the portal of the registry
7
| General | Details |
|---|---|
| Name | INDESIT D2I HL326 Full Size Integrated Dishwasher |
| Make | INDESIT |
| Language | English |
| Filetype | PDF (Download) |
| File size | 2.07 MB |
(1 votes, average: 5.00 out of 5)
Loading...
INDESIT D2I HL326 Full Size Dishwasher
Indesit D2F HD624 A Separate Dishwasher
Indesit 869991713220 Dishwasher
INDESIT I0F D641A X Free Standing Dishwasher
Indesit I0F D641A Dishwasher
INDESIT DFE 1B19 14 Dishwasher
INDeSIT D2F Dishwasher
INDeSIT D2I HD524 A Dishwasher
INDESIT W11667630 B Dishwasher
InDeSIT IN2FE10CS90S Dishwasher
GRUNDIG GSV 428420 Dishwasher
TESLA WD690MW Dishwasher
FISHER PAYKEL DD60DDFB9 Sanitise Dishwasher
BOSCH SMV4HCX48E Dishwasher
Whirlpool D2I HD526 A Dishwasher
FISHER AND PAYKEL DD24DDFTX9 N Contemporary Tall Dishwasher
BOSCH SGS2HKI66G Dishwasher
IKEA RENGOERA Dishwasher
Midea MDC17P0ABB Dishwasher
KLEENmaid DW6031 Dishwasher