MONOGRAM CDT845P4NW2 Interior Dishwasher
Dishwasher Installation
CONNECT POWER SUPPLY
PRETEST CHECKLIST
STEP 16
STEP 17
Review this list after installing your dishwasher to
avoid charges for a service call that is not covered
by your warranty.
If a power cord with plug is already installed
proceed to Step 17.
ꢀ Check to be sure power is OFF.
WARNING
ꢀ Open door and remove all foam and paper
packaging.
If house wiring is not 2-wire with ground, a ground
must be provided by the installer. When house wiring
is aluminum, be sure to use UL-Listed anti-oxidant
compound and aluminum-to-copper connectors.
ꢀ Locate the Owner’s Manual set aside earlier.
ꢀ Read the Owner’s Manual for operating instructions.
ꢀ Check door opening and closing. If door does not
open and close freely, check for proper routing of
spring cable over pulley. If door drops or closes
when released, adjust spring tension. See Step 2.
In this step you will need the junction box cover and
the #10 Hex head screw from the screws set aside
earlier.
ꢀ Secure house wiring to the back of the junction box
with a strain relief.
ꢀ Check to be sure that wiring is secure under the
dishwasher, not pinched or in contact with door
springs or other components. See Step 16.
ꢀ Locate the 3 dishwasher wires, (white, black and
green) with the stripped ends coming out of the AC
jumper. Use UL listed wire nuts of appropriate size to
connect incoming ground to green, white to white and
black to black.
ꢀ Check door alignment with tub. If door hits tub, level
dishwasher. See Step 12.
ꢀ Check door alignment with cabinet. If door hits
cabinet, reposition dishwasher. See Step 11.
ꢀ Install the junction box cover using #10 hex head
screw. Check to be sure that wires are not pinched
under the cover.
ꢀ Check that door spring does not contact water line,
fill hose, wiring or other components. See Step 11.
ꢀ Verify water supply and drain lines are not kinked
or in contact with other components. Contact with
motor or dishwasher frame could cause noise.
ꢀ Make sure that the junction box cover is resting on
the mounting bracket.
ꢀ If using a Power Cord Kit, use GE Appliances part
number WX09X70910 or WX09X70911 and refer to
the included instructions.
ꢀ Turn on the sink hot water faucet and verify water
temperature. Incoming water temperature must be
between 120°F and 140°F. A minimum of 120°F
temperature is required for best wash performance.
See “Prepare Hot Water Line,” page 5.
Ground
Screw
Ground
(Green)
AC Power
Connector
ꢀ Add 1 quart of water to the bottom of the dishwasher
to lubricate the pump seal.
ꢀ Turn on water supply. Check for leaks. Tighten
connections if needed.
ꢀ Remove protective film if present from the control
panel and door.
ꢀ Check that tub trim does not contact the door.
Junction
Black Strain White
Relief
Box
Bracket
Junction
Box Cover
NOTE: All ground screws, brackets and wires must
remain intact.
21
| General | Details |
|---|---|
| Name | MONOGRAM CDT845P4NW2 Interior Dishwasher |
| Make | MONOGRAM |
| Language | English |
| Filetype | PDF (Download) |
| File size | 33.22 MB |
(1 votes, average: 5.00 out of 5)
Loading...
MONOGRAM UDT165SIVII 18 Inch Dishwasher
MONOGRAM ZDT925SINII Dishwasher
MONOGRAM ZDT985SINII Dishwasher
MONOGRAM ZDT985SINII Fully Integrated Dishwasher
FISHER PAYKEL DD24SI9 N Dishwasher
Haier HDW15V2 Dishwasher
BOSCH SPV6EMX65Q Dishwasher
Magic Chef MCSCD6W3 Countertop Dishwasher
Hotpoint HSFC 3T127 C Dishwasher
FISHER AND PAYKEL DW60UN2B2 Built Under Dishwasher
HJC V31 Carbon Dishwasher
beko DIT39434C2 Fully Integrated Dishwasher
BOSCH SMS6ZDI11E-38 Dishwasher
BOSCH SHE3AEE5N Dishwasher