Home > MONOGRAM > MONOGRAM CDT845P4NW2 Interior Dishwasher

MONOGRAM CDT845P4NW2 Interior Dishwasher

Dishwasher Installation  
INSTALL MOUNTING  
INSTALL MOUNTING  
STEP 10  
STEP 10  
BRACKETS  
BRACKETS (CONT.)  
You will need the mounting brackets set aside  
earlier.  
Install mounting brackets on sides if the  
countertop is granite or similar material that  
will not accept wood screws:  
You must install the mounting brackets onto the  
dishwasher tub frame top OR sides prior to sliding the  
dishwasher into place under the countertop.  
ꢀ Break off front portion of the bracket with pliers at the  
location shown prior to attaching to dishwasher.  
ꢀ Install the brackets by inserting the tabs through the  
slots on the tub frame as shown. NOTE: You may  
need to work the tabs through the slots.  
Using pliers, bend and twist the tabs to secure as  
shown.  
Install mounting brackets on top if the  
underside of countertop is wood or wood-like  
material that accepts screws:  
Install the brackets by inserting the tabs through the  
slots on the tub frame as shown. NOTE: You may  
need to work the tabs through the slots.  
Side Mounting  
Insert the  
Insert the bracket tabs  
into the tub slots  
bracket  
Top  
Mounting  
tabs into  
the tub  
slots  
Using pliers,  
bend and twist  
the tabs upward to  
secure  
Bend and break here  
after installing if  
counter has a short  
overhang.  
Bracket  
Tub Frame  
Bracket  
Using pliers,  
bend and  
twist the  
tabs  
Bend and break  
here as necessary  
Tub Frame  
upward  
to secure  
PUSH DISHWASHER  
INTO FINAL POSITION  
STEP 11  
Check the tub insulation blanket, if equipped, to be  
sure it is smoothly wrapped around the tub. It should  
not be “bunched up” and it must not interfere with  
the door springs. If the insulation is “bunched up” or  
interfering with the springs, straighten and re-center  
the blanket prior to sliding the dishwasher into its  
final position.  
Using pliers, bend and twist the tabs upward to secure  
as shown.  
IMPORTANT - After installing brackets and before  
closing the dishwasher door, adjust the brackets  
by bending them up as needed, so that they do not  
contact the top of the dishwasher door and cause  
damage.  
ꢀ Slide the dishwasher into the final position by  
pushing on the sides of the door panel. Do not push  
or pull the door in a partially open or closed position  
when moving the dishwasher. Do not use a knee or  
push on the center of the panel. If you do, damage to  
the panel will likely result. Check that the dishwasher  
is squarely positioned in the cabinet opening at  
both the top and the bottom of the appliance prior to  
mounting to the cabinet.  
ꢀ If you are installing the dishwasher under a counter  
with a short overhang, the countertop brackets may  
extend beyond the edge of the counter. If this is  
the case, remove the excess length by repeatedly  
bending the brackets at the front notch only until they  
break.  
IMPORTANT Before opening the dishwasher door,  
be certain the edges of the dishwasher door panel  
are behind the face of the adjacent cabinet and not  
up against the cabinet face. Refer to Figure U. If the  
dishwasher door is opened when the edge of the door  
is against the face of the cabinet, dishwasher door  
damage and cabinet damage will occur.  
17  
GeneralDetails
NameMONOGRAM CDT845P4NW2 Interior Dishwasher
MakeMONOGRAM
LanguageEnglish
FiletypePDF (Download)
File size33.22 MB
Download PDF
1 Star2 Stars3 Stars4 Stars5 Stars (1 votes, average: 5.00 out of 5)
Loading...
MONOGRAM UDT165SIVII 18 Inch Dishwasher
MONOGRAM UDT165SIVII 18 Inch Dishwasher
MONOGRAM ZDT925SINII Dishwasher
MONOGRAM ZDT925SINII Dishwasher
MONOGRAM ZDT985SINII Dishwasher
MONOGRAM ZDT985SINII Dishwasher
MONOGRAM ZDT985SINII Fully Integrated Dishwasher
MONOGRAM ZDT985SINII Fully Integrated Dishwasher

MONOGRAM CDT845P4NW2 Interior Dishwasher