caple DI641 Dishwasher
WATER SUPPLY AND DRAIN
CONNECTION OF DRAIN HOSES
Insert the drain hose into a drain pipe with a minimum diameter of 4 cm, or let it run into the sink,
making sure to avoid bending or crimping it. The height of drain pipe must be less than 100cm.
The free end of the hose must not be immersed in water to avoid the back flow of it.
COLD WATER CONNECTION
Cold water connection Connect the cold water
supply hose to a threaded 3/4 inch connector
and make sure that it is fastened tightly in place.
If the water pipes are new or have not been
used for an extended period of time, let the
water run to make sure that the water is clear.
This precaution is needed to avoid the risk of the
water inlet to be blocked and damaged.
Counter
ordinary supply hose
safety supply hose
Back of dishwasher
A
ABOUT THE SAFETY SUPPLY HOSE
The safety supply hose consists of the double walls. The hose’s system guarantees its intervention
by blocking the flow of water in case of the supply hose breaking and when the air space between
the supply hose itself and the outer corrugated hose is full of water.
Drain hose
B
Water Inlet
Drain Pipe
WARNING
A hose that attaches to a sink spray can burst if it is installed on the same water line as the
dishwasher. If your sink has one, it is recommended that the hose be disconnected and the
hole plugged.
Please securely fix the drain hose
in either position A or position B
Mains Cable
HOW TO CONNECT THE SAFETY SUPPLY HOSE
1. Pull The safety supply hoses completely out from storage compartment located at rear
of dishwasher.
HOW TO DRAIN EXCESS WATER FROM HOSES
If the sink is higher than 100cm from the floor, the excess water in hoses cannot be drained
directly into the sink. It will be necessary to drain excess water from hoses into a bowl or suitable
container that is held outside and lower than the sink.
2. Tighten the screws of the safety supply hose to the faucet with thread 3/4inch.
3. Turn water fully on before starting the dishwasher.
WATER OUTLET
Connect the water drain hose. The drain hose must be correctly fitted to avoid water leaks. Ensure
that the water drain hose is not kinked or squashed.
HOW TO DISCONNECT THE SAFETY SUPPLY HOSE
1. Turn off the water.
EXTENSION HOSE
If you need a drain hose extension, make sure to use a similar drain hose. It must
be no longer than 4 metres; otherwise the cleaning effect of the dishwasher could be reduced.
2. Unscrew the safety supply hose from the faucet.
SYPHON CONNECTION
The waste connection must be at a height less than 100 cm (maximum) from the bottom of the
dishwasher. The water drain hose should be fixed.
32 Instruction manual DI641 Please keep this instruction manual for future reference
Please keep this instruction manual for future reference Instruction manual DI641
33
| General | Details |
|---|---|
| Name | caple DI641 Dishwasher |
| Make | caple |
| Language | English |
| Filetype | PDF (Download) |
| File size | 3.62 MB |
(1 votes, average: 5.00 out of 5)
Loading...
caple DI654 Dishwasher
caple DI631 Dishwasher
gorenje GV52040 Dishwasher
reg 10789234 Dishwasher
FISHER and PAYKEL DD60DHI9 Dishwasher
FISHER AND PAYKEL DW60U4I2 Dishwasher
Electrolux EEA27200L Dishwasher
GAGGENAU DF480801 Dishwasher
FISHER PAYKEL DW60UD6X Sanitise Built Under Dishwasher
Haier HDW15F3B1 Dishwasher
COMFEE TD802 Table Top Dishwasher
LG Electronics LDPS6762S 23.75 in. PrintProof Smart Dishwasher