Home > GE Appliances > GE APPLIANCES DT605PSMSS with Plastic Interior Dishwasher
GE APPLIANCES DT605PSMSS with Plastic Interior Dishwasher
Installation Preparation
PREPARE DISHWASHER ENCLOSURE
WARNING
To reduce the risk of electric shock, fire, or injury to
persons, the installer must ensure that the dishwasher
is completely enclosed at the time of installation.
This Wall Area
Must be Free
of Pipes and
Wires
ADVERTENCIA
24”
Min.
33-1/2” to 34-3/4”
Underside of
Countertop
toFloor
Para reducir el riesgo de descarga eléctrica, incendio
o lesiones a personas, el instalador debe asegurarse
de que el lavaplatos esté completamente cerrado en el
momento de la instalación.
4”
Plumbing and Electric Service
Must Enter Inside This Area
Cabinets
Square
and
DISHWASHER HANDLE DIMENSION: The dishwasher
door should be flush with the cabinet. For models with
a handle, the total depth (with handle) is 26-1/4” max.
depending on the model. Locate the Quick Specs document
online for more dishwasher dimensions.
6”
Plumb
24”
Min.
CLEARANCES: When installed into
a corner, allow 2” min. clearance
between dishwasher and adjacent
cabinet, wall or other appliances.
Allow 25-1/2” min. clearance from
the front of the dishwasher for
door opening.
Countertop
• The rough cabinet opening must be at least 24” deep,
24” wide and approximately 34-1/2” high from floor to
underside of the countertop.
Dishwasher
• The dishwasher must be installed so that drain hose is
no more than 16’ in length for proper drainage.
25-1/2"
• The dishwasher must be fully enclosed on the top,
sides and back, and must not support any part of the
enclosure.
Clearance for Door
Opening 2" Minimum
DRAIN REQUIREMENTS
• Follow local codes and ordinances.
• Do not exceed 16’ distance to drain.
Method 1 – Air Gap with Waste Tee or Disposer
An air gap must be used when required by local codes
and ordinances. The air gap must be installed according
to manufacturer’s instructions.
NOTE : Air gap must be used if waste tee or disposer
connection is less than 18” above floor to prevent siphoning.
DETERMINE DRAIN METHOD
The type of drain installation depends on the following
questions.
72”
max.
72”
max.
• Do local codes or ordinances require an air gap?
• Is waste tee less than 18” above floor?
If the answer to either question is YES, Method 1
MUST be used.
Method 2 – “High Drain Loop” with Waste Tee or Disposer
• If the answers are NO, either method may be used.
Drain Hose Hanger
Drain Hose Hanger
CABINET PREPARATION
• Drill a 1-1/2” diameter hole in the cabinet wall within
the shaded areas shown in PREPARE DISHWASHER
ENCLOSURE section for the drain hose connection.
The hole should be smooth with no sharp edges.
32” min. -
32” min. -
72” max.
18”
72” max.
18”
min.
min.
IMPORTANT – When connecting
drain line to disposer, check to be sure
that drain plug has been removed.
DISHWASHER WILL NOT DRAIN IF
PLUG IS LEFT IN PLACE.
Remove
Drain
Plug
Tip: Avoid unnecessary service call charges.
Always be sure disposer drain plug has been removed
before attaching dishwasher drain hose to the disposer.
3
| General | Details |
|---|---|
| Name | GE APPLIANCES DT605PSMSS with Plastic Interior Dishwasher |
| Make | GE Appliances |
| Language | English |
| Filetype | PDF (Download) |
| File size | 10.94 MB |

GE APPLIANCES GTW845 Dishwasher

GE APPLIANCES GSD2100VBB Dishwasher

GE APPLIANCES GDF550PGR Plastic Interior Dishwasher with Front Controls

GE APPLIANCES PDT755SYV/BTV UltraFresh System Dishwasher with Interior

GE APPLIANCES GDT670SGV Interior Dishwasher with Hidden Controls

GE APPLIANCES GDT650SYV Interior Dishwasher with Hidden Controls

GE APPLIANCES PDP715SYVFS GE Profile Series Interior Dishwasher

GE APPLIANCES PDT715SYV Interior Dishwasher with Hidden Controls

GE APPLIANCES PDT705SYWFS Dishwasher

GE APPLIANCES GDT565HSYSS Energy Star Hybrid Tub Dishwasher













































