INDESIT I0F D641A X Free Standing Dishwasher
TROUBLESHOOTING
In case your dishwasher doesn’t work properly, check if the problem can be solved by going through the following list. For other
errors or issues please contact authorized After-sales Service which contact details can be found in the warranty booklet. Spare
parts will be available for a period of either up to 7 or up to 10 years, according to the specific Regulation requirements.
PROBLEMS POSSIBLE CAUSES
SOLUTIONS
Salt reservoir is empty (after refill the salt indicator may Refill reservoir with salt (for more information - see page 2).
Salt
indicator is lit
remain lit for several wash cycles).
Adjust water hardness (see table, page 2).
Rinse aid dispenser is empty (after refill the rinse aid
indicator may remain lit for several wash cycles).
Rinse aid
indicator is lit
Refill dispenser with rinse aid (for more information - see page 2).
Insert the plug into the socket.
The appliance has not been plugged in properly.
Power outage.
For safety reasons, dishwasher will not restart automatically when power returns.
Press the START/Pause button to resume the cycle.
The dishwasher
won’t start or does
not respond to
commands.
The dishwasher door is not closed.
Auto Door pin is not pulled in.
Vigorously push the door until you hear the “click”.
Cycle is interupted by door opening for > 4 sec.
Close the door and press START/Pause button.
It does not respond to commands. Display shows:
Switch off the appliance by pressing the ON/OFF button, switch it back on after
F9 or F12 and both On/Off and START/Pause LEDs approximately one minute and restart the program. If problem persists, unplug the
are blinking rapidly.
appliance for 1 minute, then plug it back in.
The wash cycle has not finished yet.
The drain hose is bent.
Wait until the wash cycle finishes.
The dishwasher
won’t drain.
Display shows: F3
and both On/Off and
START/Pause LEDs
are blinking rapidly.
Check that the drain hose is not bent (see INSTALATION INSTRUCTION).
Clean the sink drain pipe.
The sink drain pipe is blocked.
The filter is clogged up with food residues.
The dishes are rattling against each other.
Clean the filter (see CLEANING THE FILTER ASSEMBLY).
Position the crockery correctly (see LOADING THE RACKS).
The dishwasher
makes
excessive noise.
The detergent has not been measured out correctly or it is not suitable for use in dish-
washers (see FILLING THE DETERGENT DISPENSER). Restart dishwasher by pressing the
DRAIN button (see OPTIONS AND FUNCTIONS) and run new program without detergent.
An excessive amount of foam has been produced.
The crockery has not been arranged properly.
Arrange the crockery correctly (see LOADING THE RACKS).
Arrange the crockery correctly (see LOADING THE RACKS).
Select an appropriate wash cycle (see PROGRAMS TABLE).
The spray arms cannot rotate freely, being hindered
by the dishes.
The wash cycle is too gentle.
The detergent has not been measured out correctly or it is not suitable for use in dish-
washers (see FILLING THE DETERGENT DISPENSER).
The dishes are not
clean.
An excessive amount of foam has been produced.
The cap on the rinse aid compartment has not been
shut correctly.
Make sure the cap of the rinse aid dispenser is closed.
The filter is soiled or clogged.
There is no salt.
Clean the filter assembly (see CARE AND MAINTENANCE).
Fill the salt reservoir (see FILLING THE SALT RESERVOIR).
The dishwasher
does not fill the wa-
ter. Display shows:
and F6, both
No water in the water supply or the tap is closed.
The inlet hose is bent.
Make sure there is water in the water supply or the tap running.
Make sure the inlet hose is not bent (see INSTALLATION) reprogram the dishwasher
and reboot.
On/Off and START/
Pause LEDs are
blinking rapidly.
The sieve in the water inlet hose is clogged; it is
necessary to clean it.
After having carried out the verification and cleaning, turn off and turn on the dish-
washer and restart a new program.
Dishwasher finishes
the cycle prematurely.
Display shows: F15
and both On/Off and
START/Pause LEDs
are blinking rapidly.
Drain hose positioned too low or siphoning into
home sewage system.
Check if end of drain hose is placed at correct height (see INSTALLATION).Check for
siphoning into home sewage system, install air admittance valve if necessary.
Air in water supply.
Check water supply for leaks or other issues letting air inside.
Policies, standard documentation, ordering of spare parts and additional product information can be found by:
•
•
•
Using QR code on your product.
Visiting our website docs.indesit.eu and parts-selfservice.europeanappliances.com
Alternatively, contact our After-sales Service (See phone number in the warranty booklet).
When contacting our After-sales Service, please state the codes provided on your product‘s identification plate.
IEC 436
:
The model information can be retrieved using the QR-Code reported in the energy label.
The label also includes the model identifier that can be used to consult the portal of the registry
8
| General | Details |
|---|---|
| Name | INDESIT I0F D641A X Free Standing Dishwasher |
| Make | INDESIT |
| Language | English |
| Filetype | PDF (Download) |
| File size | 15.94 MB |

INDESIT D2I HL326 Full Size Dishwasher

Indesit D2F HD624 A Separate Dishwasher

Indesit 869991713220 Dishwasher

Indesit I0F D641A Dishwasher

INDESIT DFE 1B19 14 Dishwasher

INDeSIT D2F Dishwasher

INDeSIT D2I HD524 A Dishwasher

INDESIT W11667630 B Dishwasher

InDeSIT IN2FE10CS90S Dishwasher

inDeSIT DSIO3M24CS Dishwasher













































