VALBERG FBI16S43A 16 Dishwasher
Using the appliance
Using the appliance
B
B
Adjusting salt consumption
Extra Drying
• The dishwasher is designed to allow for adjustment in the amount of salt consumed based
on the hardness of the water used. This is intended to optimise and customise the level of
salt consumption.
To dry dishes more completely. ( It can only be used with
Hygiene, Universal, ECO, Glass, 58 min )
Strong wash
To wash very dirty, hard to clean dishes. ( It can only be used
with Hygiene, Universal, ECO, Glass, 58 min )
• Please follow the steps below for adjustment in salt consumption.
1. Open the door, switch on the appliance;
Turbo speed+
Reduce the program time. ( It can only be used with Hygiene,
Universal, ECO, Glass, 58 min, Self-cleaning )
Function
indicator
9
2. Within 60 seconds after the appliance was switched on, press the Program button “>” for
more than 5 seconds, then enter the water softener setting mode.
Auto open
After washing the door will open automatically to achieve
better drying effect (Rapid and self-cleaning programs don’t
have this function.)
3. Press the ‘>’ button again to select the proper set according to your local environment, the
setting will change in the following sequence: H3->H4->H5->H6->H1->H2;
When you press the button for 3 seconds, the button will
light on when a certain program is selected. You can cancel
the auto-open function for 3 seconds again, corresponding
indicator will go off.
4. Without operation in 5 seconds or press the Power button to complete the setup and exit
the setup mode.
WATER HARDNESS
Regeneration
occurs every
X program
Salt
consumption
(gram/cycle)
Upper
Water softner
level
German
°dH
French
°fH
British
°Clarke
When you select Upper, only the dishes in the upper rack will
be washed. The spray system of the lower basket will not
operate.
Mmol/l
sequence 1)
Alt
indicator
No
10
0 - 5
0 - 9
0 - 6
0 - 0,94
1,0 - 2,0
H1
0
Lower
regeneration
When you select Lower, only the dishes in the lower rack will
be washed. The spray system of the upper basket will not
operate.
6 - 11
10 - 20
7 - 14
H2
H3
H4
H5
H6
10
5
9
12 - 17 21 - 30 15 - 21 2,1 - 3,0
18 - 22 31 - 40 22 - 28 3,1 - 4,0
23 - 34 41 - 60 29 - 42 4,1 - 6,0
35 - 55 61 - 98 43 - 69 6,1 - 9,8
12
20
30
60
3
Water softener
2
• The water softener must be set manually, using the water hardness dial.
1
• The water softener is designed to remove minerals and salts from the water, which would
have a detrimental or adverse effect on the operation of the appliance.
1°dH=1.25 °Clarke=1.78 °fH=0.178mmol/l
The factory setting: H3
• The more minerals there are, the harder your water is.
1)
Every cycle with a regeneration operation consumes additional 4.0 litres of water, the
energy consumption increases by 0.06 kWh and the program extents by 10 minutes.
• The softener should be adjusted according to the hardness of the water in your area.
• Your local Water Authority can advise you on the hardness of the water in your area.
NOTE
Please check the “Loading The Salt Into The Softener”, if
your dishwasher lacks salt.
24
EN
25
EN
| General | Details |
|---|---|
| Name | VALBERG FBI16S43A 16 Dishwasher |
| Make | VALBERG |
| Language | English |
| Filetype | PDF (Download) |
| File size | 31.47 MB |
(1 votes, average: 5.00 out of 5)
Loading...
VALBERG SAD929C Dishwasher
VALBERG 14S44 C XAD929C,14S44 C DXAD929C Dishwasher
VALBERG VAL12C47SSC Dishwasher
VALBERG 14S40 B WAD929C Dishwasher
VALBERG XAD929C Dishwasher
Classeq C500-30D Undercounter Dishwasher
SAMSUNG DW60CB750UAPSA Bespoke Built Under Dishwasher
BOSCH SMI6ZCS13E Dishwasher
BOSCH SBT4ECX10E Dishwasher
MONOGRAM UDT165SIVII 18 Inch Dishwasher
FISHER and PAYKEL DD60ST4ZB9 Contemporary Tall Dishwasher
BOSCH SMS4EMW01E-30 Dishwasher
FISHER PAYKEL DD24DTX6PX1 Sanitize Dishwasher
INVENTUM VVW6008AW Dishwasher
Miele G 7131 SCi AD 125 Edition Dishwasher