Indesit D2F HD624 A Separate Dishwasher
EN
Quick Guide
ECO program data is measured under laboratory conditions according to European Standard EN 60436:2020. Note for Test Laboratories: For information on
comparative EN testing conditions, please send an email to the following address: dw_test_support@whirlpool.com
Pre-treatment of the dishes is not needed before any of the programs.
*) Not all options can be used simultaneously.
**) Values given for programs other than the program Eco are indicative only. The actual time may vary depending on many factors such as temperature and
pressure of the incoming water, room temperature, amount of detergent, quantity and type of load, load balancing, additional selected options and sensor cali-
bration. The sensor calibration can increase program duration up to 20 min.
Please scan the QR code on your product in order to have more detailed information.
OPTIONS AND FUNCTIONS
OPTIONS can be selected directly by pressing the corresponding button (see CONTROL PANEL). If an option is not compatible with the selected
program (see PROGRAMS TABLE), the corresponding LED flashes rapidly 3 times and beeps will sound. The option will not be enabled.
HALF LOAD - If there are not many dishes to be washed, a half loading
may be used in order to save water, electricity and detergent.
Remember to halve the amount of detergent.
DELAY -The start of the program may be delayed for a period of time
between 0:30 and 24 hours
The DELAY function cannot be set once a wash cycle has been started.
TABLET (Tab)- If you use powder or liquid detergent, this option
should be off.
WATER TAP CLOSED – Alarm
Flashes when there is no inlet water or water tap is closed.
PUSH&GO - Push&Go button is an easily distinguishable button that
allows you direct access to the Push&Go program, a wash and dry cycle
that ensures great cleaning performance in a short time. You don’t have to
worry which program to choose, Push&Go cycle will do the work for you.
DRAIN OUT - To stop and cancel the active cycle, the Drain Out
function can be used. A long press of START/PAUSE button, will
activate the DRAIN OUT function. The active program will be stopped and
the water in the dishwasher will be drained out.
CAPACITY: 14 standard place-settings
LOADING THE RACKS
FOLDABLE
FLAPS WITH
ADJUSTABLE
POSITION
CUTLERY BASKET
The basket is
UPPER RACK
LOWER RACK
For pots, lids, plates, sa-
equipped with top
grilles for impro-
ved cutlery arran-
gement. The cutle-
ry basket should
be positioned only
at the front of the
lower rack.
lad bowls, cutlery etc.
Large plates and lids
should ideally be pla-
ced at the sides to avo-
id interferences with
the spray arm.
The lower rack has tip-
-up supports which
can be used in a verti-
cal position when ar-
ranging plates or in a
horizontal position (lo-
wer) to load pans and
salad bowls easily.
Knives and other utensils with sharp
edges must be placed in the cutlery
basket with the points facing down-
wards or they must be positioned
horizontally in the tip-up compart-
ments on the upper rack.
(loading example for the
lower rack)
(loading example for the upper rack)
Load delicate and light dishes: glasses,
cups, saucers, low salad bowls.
More information in the Daily Reference Guide on website.
CLEANING AND MAINTENANCE
CLEANING THE FILTER ASSEMBLY
CLEANING THE SPRAY ARMS
B
A
A
C
I
n case you find foreign objects (such as broken glass, porcelain, bones, fruit seeds etc.) To remove the upper spray arm, The lower spray arm may
please remove them carefully. turn the plastic locking ring in a be removed by pulling it
NEVER REMOVE the wash-cycle pump protection (black detail) (Fig 4). clockwise direction. upwards.
Please scan the QR code on your product in order to have more detailed information.
TROUBLESHOOTING
PROBLEMS
POSSIBLE CAUSES
SOLUTIONS
The dishwasher does
not fill the
water. Display shows:
and F6, both On/Off
and START/Pause LEDs
are blinking rapidly.
No water in the water supply or the tap is closed.
The inlet hose is bent.
Make sure there is water in the water supply or the tap running.
Make sure the inlet hose is not bent (see INSTALLATION) reprogram the dishwasher and
reboot.
The sieve in the water inlet hose is clogged; it is
necessary to clean it.
After having carried out the verification and cleaning, turn off and turn on the dishwa-
sher and restart a new program.
Dishwasher finishes
the cycle prematurely.
Display shows: F15 and
both On/Off and START/
Pause LEDs are blinking
rapidly.
Drain hose positioned too low or siphoning into
home sewage system.
Check if end of drain hose is placed at correct height (see INSTALLATION).Check for
siphoning into home sewage system, install air admittance valve if necessary.
Air in water supply.
Check water supply for leaks or other issues letting air inside.
Policies, standard documentation, ordering of spare parts and additional product information can be found by:
•
•
•
Using QR code on your product.
Visiting our website docs.indesit.eu and parts-selfservice.whirlpool.com
Alternatively, contact our After-sales Service (See phone number in the warranty booklet).
When contacting our After-sales Service, please state the codes provided on your product‘s identification plate.
The model information can be retrieved using the QR-Code reported in the energy label.
IEC 436
:
2
| General | Details |
|---|---|
| Name | Indesit D2F HD624 A Separate Dishwasher |
| Make | INDESIT |
| Language | English |
| Filetype | PDF (Download) |
| File size | 11.81 MB |

INDESIT D2I HL326 Full Size Dishwasher

Indesit 869991713220 Dishwasher

INDESIT I0F D641A X Free Standing Dishwasher

Indesit I0F D641A Dishwasher

INDESIT DFE 1B19 14 Dishwasher

INDeSIT D2F Dishwasher

INDeSIT D2I HD524 A Dishwasher

INDESIT W11667630 B Dishwasher

InDeSIT IN2FE10CS90S Dishwasher

inDeSIT DSIO3M24CS Dishwasher





























