INDeSIT D2F HK26 Dishwasher
FIRST TIME USE
SALT, RINSE AID AND DETERGENT
ADVICE REGARDING THE FIRST TIME USE FILLING THE RINSE AID DISPENSER
After installation, remove the stoppers from the racks and the retaining Rinse aid makes dish DRYING easier. The rinse aid dispenser A should be
filled when when the dark optical indicator on the dispenser door C
becomes transparent.
elastic elements from the upper rack.
FILLING THE SALT RESERVOIR
The use of salt prevents the formation of LIMESCALE on the dishes and
on the machine’s functional components.
C
•
•
It is mandatory that THE SALT RESERVOIR NEVER BE EMPTY.
It is important to set the water hardness.
The salt reservoir is located in the lower part of the dishwasher
(see PRODUCT DESCRIPTION) and must be filled when the SALT REFILL
indicator light
in the control panel is lit.
B
A
1. Remove the lower rack and unscrew the
reservoir cap (anticlockwise).
2. Only the first time you do this: fill the salt
reservoir with water.
3. Position the funnel (see figure) and fill the salt
reservoir right up to its edge (approximately
1 kg); it is not unusual for a little water to leak
out.
4. Remove the funnel and wipe any salt residue
away from the opening.
1. Open the dispenser B by pressing and pulling up the tab on the lid.
2. Pour in the rinse aid (max.110 ml), making sure it does not overflow
from the dispenser. If this happens, clean the spill immediately with
a dry cloth.
3. Press the lid down until you hear a click to close it.
NEVER pour the rinse aid directly into the appliance tub.
ADJUSTING THE DOSAGE OF RINSE AID
If you are not completely satisfied with the drying results, you can ad-
just the quantity of rinse aid used.
Make sure the cap is screwed on tightly, so that no detergent can get
into the container during the wash program (this could damage the
water softener beyond repair).
Whenever you need to add salt, it is mandatory to complete the
procedure before the beginning of the washing cycle to avoid corrosion.
• Switch the dishwasher on using the ON/OFF button.
• Switch it off using the ON/OFF button.
• Press button START/Pause three times.
• Switch it on using the ON/OFF button.
• The START/Pause LED light will flash as many times as the level that
was set.
SETTING THE WATER HARDNESS
To allow the water softener to work in a perfect way, it is essential that
the water hardness setting is based on the actual water hardness in
your house. This information can be obtained from your local water
supplier.
• Set the level of rinse aid quantity to be supplied using the PROGRAM
SELECTION knob (see PROGRAMS TABLE).
• Switch it off using the ON/OFF button
The factory sets the default value for the water hardness
• Switch on the appliance by pressing the ON/OFF button.
• Switch off the appliance by pressing the ON/OFF button.
• Hold down button START/Pause for 5 seconds.
Setting is complete!
If the rinse aid level is set to 1 (ECO), no rinse aid will be supplied.
A maximum of 5 levels can be set according to the dishwasher model.
The factory setting is specific to the model, please follow instruction
above to check this for your machine.
• If you see bluish streaks on the dishes, set a low number (2-3).
• If there are drops of water or limescale marks on the dishes,
set a mid-range number (4-5).
• Switch on the appliance by pressing the ON/OFF button.
• The ON/OFF LED light will flash as many times as the level that was set.
• Set the desired water hardness level using the PROGRAM SELECTION
knob (see WATER HARDNESS TABLE).
Water Hardness Table
FILLING THE DETERGENT DISPENSER
°dH
German
degrees
°fH
French
degrees
°Clark
English
degrees
To open the detergent dispenser use the opening device D.
Introduce the detergent into the dry dispenser E only. Place the
amount of detergent for pre-washing directly inside the tub.
Level
1
2
Soft
0 - 6
0 - 10
0 - 7
1. When measuring out the detergent
refer to the mentioned earlier infor-
mation to add the proper quantity.
Medium
Average
Hard
7 - 11
11 - 20
8 - 14
3
4
5
12 - 16
17 - 34
35 - 50
21 - 29
30 - 60
61 - 90
15 - 20
21 - 42
43 - 62
Inside the dispenser E there are
indications to help the detergent
dosing.
2. Remove detergent residues from
E
D
Very hard
the edges of the dispenser and clo-
se the cover until it clicks.
3. Close the lid of the detergent
dispenser by pulling it up until the
closing device is secured in place.
• Switch off the appliance by pressing the ON/OFF button.
Setting is complete!
As soon as this procedure is complete, run a program without loading.
Only use salt that has been specifically designed for dishwashers.
The detergent dispenser automatically opens up at the right time
according to the program.
After the salt has been poured into the machine, the SALT REFILL indi-
cator light switches off.
Usage of detergent not designed for dishwashers may cause mal-
function or damage to the appliance.
If the salt container is not filled, the water softener and the heating
element may be damaged as a result of limescale accumulation.
Using of Salt is recommended with any type of dishwasher detergent.
2
| General | Details |
|---|---|
| Name | INDeSIT D2F HK26 Dishwasher |
| Make | INDESIT |
| Language | English |
| Filetype | PDF (Download) |
| File size | 4.16 MB |
(1 votes, average: 5.00 out of 5)
Loading...
INDESIT D2I HL326 Full Size Dishwasher
Indesit D2F HD624 A Separate Dishwasher
Indesit 869991713220 Dishwasher
INDESIT I0F D641A X Free Standing Dishwasher
Indesit I0F D641A Dishwasher
INDESIT DFE 1B19 14 Dishwasher
INDeSIT D2F Dishwasher
INDeSIT D2I HD524 A Dishwasher
INDESIT W11667630 B Dishwasher
InDeSIT IN2FE10CS90S Dishwasher
BOSCH SMV4EVX14E Dishwasher
BOSCH SHP88CL5N Custom Panel Dishwasher
BOSCH SHV53CM3N 300 Series Full Dishwasher
FISHER and PAYKEL DD60SHTI9 Tall Dishwasher
FISHER and PAYKEL DW60U4HI2 Dishwasher
BOSCH SMV4HCX52E-39 Dishwasher
gorenje GI62040X Dishwasher
FISHER PAYKEL DD24SV2T9 Dishwasher
FRIGIDAIRE FDPH4316A Dishwasher
beko BDFN26450A Dishwasher