INDeSIT D2F HK26 Dishwasher
TROUBLESHOOTING
In case your dishwasher doesn’t work properly, check if the problem can be solved by going through the following list.
For other errors or issues please contact authorized After-sales Service which contact details can be found in the warranty booklet.
Spare parts will be available for a period of either up to 7 or up to 10 years, according to the specific Regulation requirements.
PROBLEMS POSSIBLE CAUSES
SOLUTIONS
Salt indicator
is lit
Salt reservoir is empty. (After refill the salt indicator Refill reservoir with salt (for more information - see page 2).
may remain lit for several wash cycles).
The appliance has not been plugged in properly.
Power outage.
Adjust water hardness - see table, page 2.
Insert the plug into the socket.
For safety reasons, dishwasher will not restart automatically when power returns.
Press the START/Pause button to resume the cycle.
The dishwasher
won’t start or does
not respond to
commands.
The dishwasher door is not closed.
Vigorously push the door until you hear the “click”.
Close the door and press the START/Pause button.
Cycle is interupted by door opening for > 4 sec.
Switch off the appliance by pressing the ON/OFF button, switch it back on after
approximately one minute and restart the program. If problem persists, unplug the
appliance for 1 minute, then plug it back in.
It does not respond to commands.
The wash cycle has not finished yet.
The drain hose is bent.
Wait until the wash cycle finishes.
Check that the drain hose is not bent (see INSTALATION INSTRUCTION).
Clean the sink drain pipe.
The dishwasher
won’t drain.
The sink drain pipe is blocked.
The filter is clogged up with food residues.
The dishes are rattling against each other.
Clean the filter (see CLEANING THE FILTER ASSEMBLY).
Position the crockery correctly (see LOADING THE RACKS).
The dishwasher
makes excessive
noise.
The detergent has not been measured out correctly or it is not suitable for use
in dishwashers (see FILLING THE DETERGENT DISPENSER). Restart dishwasher by
pressing the DRAIN button (see OPTIONS AND FUNCTIONS) and run new program
without detergent.
An excessive amount of foam has been produced.
The crockery has not been arranged properly.
Arrange the crockery correctly (see LOADING THE RACKS).
Arrange the crockery correctly (see LOADING THE RACKS).
Select an appropriate wash cycle (see PROGRAMS TABLE).
The spray arms cannot rotate freely, being hindered
by the dishes.
The wash cycle is too gentle.
The detergent has not been measured out correctly or it is not suitable for use in
dishwashers (see FILLING THE DETERGENT DISPENSER).
The dishes are not
clean.
An excessive amount of foam has been produced.
The cap on the rinse aid compartment has not been
shut correctly.
Make sure the cap of the rinse aid dispenser is closed.
The filter is soiled or clogged.
There is no salt.
Clean the filter assembly (see CARE AND MAINTENANCE).
Fill the salt reservoir (see FILLING THE SALT RESERVOIR).
Make sure there is water in the water supply or the tap running.
No water in the water supply or the tap is closed.
The dishwasher
does not fill the
water.
Make sure the inlet hose is not bent (see INSTALLATION) reprogram the dishwasher
and reboot.
The inlet hose is bent.
All LEDs are
blinking rapidly.
The sieve in the water inlet hose is clogged; it is
necessary to clean it.
After having carried out the verification and cleaning, turn off and turn on the
dishwasher and restart a new program.
Drain hose positioned too low or siphoning into
home sewage system.
Check if end of drain hose is placed at correct height (see INSTALLATION). Check for
siphoning into home sewage system, install air admittance valve if necessary.
Dishwasher finishes
the cycle prema-
turely.
Air in water supply.
Check water supply for leaks or other issues letting air inside.
Policies, standard documentation, ordering of spare parts and additional product information
can be found by:
•
•
•
Visiting our website docs.indesit.eu and parts-selfservice.whirlpool.com
Using QR Code
Alternatively, contact our After-sales Service (See phone number in the warranty booklet).
When contacting our After-sales Service, please state the codes provided on your product‘s
identification plate.
IEC 436
:
The model information can be retrieved using the QR-Code reported in the energy label.
The label also includes the model identifier that can be used to consult the portal of the registry at
400011651802B
11/2022 dk - Xerox Fabriano
8
| General | Details |
|---|---|
| Name | INDeSIT D2F HK26 Dishwasher |
| Make | INDESIT |
| Language | English |
| Filetype | PDF (Download) |
| File size | 4.16 MB |
(1 votes, average: 5.00 out of 5)
Loading...
INDESIT D2I HL326 Full Size Dishwasher
Indesit D2F HD624 A Separate Dishwasher
Indesit 869991713220 Dishwasher
INDESIT I0F D641A X Free Standing Dishwasher
Indesit I0F D641A Dishwasher
INDESIT DFE 1B19 14 Dishwasher
INDeSIT D2F Dishwasher
INDeSIT D2I HD524 A Dishwasher
INDESIT W11667630 B Dishwasher
InDeSIT IN2FE10CS90S Dishwasher
BOSCH SMV8ZCX00X Dishwasher
FISHER AND PAYKEL DD60D4HNX9 Dishwasher
Haier HDW15V2S2 Dishwasher
SAMSUNG DW80B70 Smart Dishwasher
FISHER PAYKEL DD24DDFTX9 N Dishwasher
SHARP SDW6767HS Dishwasher
BOSCH SGV4HCX48E Dishwasher
beko BDIN38651C Dishwasher
CDA CDI6132 Dishwasher
IKEA AA-2412050-2-1 LAGAN Dishwasher