indesit DFG 15B1 Built Dishwasher
Installation and Assistance
The hose should not be bent or compressed.
If the appliance must be moved at any time, keep it in an
upright position; if absolutely necessary, it may be tilted onto its
back.
EN
Connecting the water outlet hose
Connect the outlet hose (without bending it) to a drain duct with
a minimum diameter of 4 cm.
The outlet hose must be at a height ranging from 40 to 80 cm
from the floor / surface where the dishwasher rests (A).
Positioning and levelling
1. Remove the appliance from all packaging and check that
it has not been damaged during transportation. If it has been
damaged, contact the retailer and do not proceed any further
with the installation process.
2. Arrange the dishwasher so that its sides or back panel are in
contact with the adjacent cabinets or the wall. This appliance
can also be recessed under a single worktop*(see the Assembly
Instruction sheet.)
3. Position the dishwasher on a level sturdy floor. If the floor
is uneven, the front feet of the appliance should be adjusted
until it reaches a horizontal position. If the appliance is levelled
correctly, it will be more stable and much less likely to move or
cause vibrations and noise while it is operating.
Before connecting the water outlet hose to the sink drain, remove
the plastic plug (B).
4*. To adjust the height of the rear foot, turn the red hexagonal
bushing on the lower central part at the front of the dishwasher
using a hexagonal spanner with an opening of 8 mm. Turn the
spanner in a clockwise direction to increase the height and in an
anticlockwise direction to decrease it (see Building-in Instruction
sheet attached to the documentation.)
Anti-flooding protection
To ensure floods do not occur, the dishwasher:
- is provided with a special system which blocks the water supply
in the event of anomalies or leaks from inside the appliance.
Some models are also equipped with the supplementary safety
device New Acqua Stop*, which guarantees anti-flooding
protection even in the event of a supply hose rupture.
Connecting the water and electricity supplies
Connection to the water and electricity supplies should only
be performed by a qualified technician.
WARNING: HAZARDOUS VOLTAGE!
The dishwasher should not stand on the water hoses or
electricity supply cable.
Under no circumstances should the water inlet hose be cut, as
it contains live electrical parts.
The appliance must be connected to the water supply
network using new hoses.
Electrical connection
Before inserting the plug into the electrical socket, make sure
that:
Never use old or second hand hose sets. Do not reuse hose
sets from any previously installed dishwasher.
•
•
The socket is earthed and complies with current regulations.
the socket can withstand the maximum load of the appliance,
which is indicated on the data plate located on the inside of
the door
The water inlet and outlet hoses and the electricity supply cable
may be positioned towards the right or the left in order to achieve
the best possible installation.
(see Description of the appliance);
The power supply voltage falls within the values indicated on
the data plate on the inside of the door.
The socket is compatible with the plug of the appliance. If
this is not the case, ask an authorised technician to replace
the plug (see Assistance); do not use extension cables or
multiple sockets.
Connecting the water inlet hose
•
•
•
To a suitable cold water connection point: before attaching
the hose, run the water until it is perfectly clear so that any
impurities that may be present in the water do not clog the
appliance; after performing this operation, screw the inlet
hose tightly onto a tap with a ¾ gas threaded connection.
To a suitable hot water connection point: your dishwasher
may be supplied with hot water from the mains supply (if you
have a central heating system with radiators) provided that it
does not exceed a temperature of 60°C.
•
Once the appliance has been installed, the power supply
cable and the electrical socket should be easily accessible.
The cable should not be bent or compressed.
Screw the hose to the tap as described for connection to a
cold water supply.
If the power supply cable is damaged, it must be replaced
by the manufacturer or its Technical Assistance Service in order
to prevent all potential hazards (see Assistance.)
If the inlet hose is not long enough, contact a specialist store
or an authorised technician (see Assistance.)
The water pressure must be within the values indicated in
the Technical Data table (see adjacent information.)
* Only available in selected models.
4
| General | Details |
|---|---|
| Name | indesit DFG 15B1 Built Dishwasher |
| Make | INDESIT |
| Language | English |
| Filetype | PDF (Download) |
| File size | 2.71 MB |
(1 votes, average: 5.00 out of 5)
Loading...
INDESIT D2I HL326 Full Size Dishwasher
Indesit D2F HD624 A Separate Dishwasher
Indesit 869991713220 Dishwasher
INDESIT I0F D641A X Free Standing Dishwasher
Indesit I0F D641A Dishwasher
INDESIT DFE 1B19 14 Dishwasher
INDeSIT D2F Dishwasher
INDeSIT D2I HD524 A Dishwasher
INDESIT W11667630 B Dishwasher
InDeSIT IN2FE10CS90S Dishwasher
FISHER PAYKEL DD60SCHTX9 Dishwasher
JENN-AIR JDAF5924RM Dishwasher
edesa 3706588 Dishwasher
IKEA SBE8596Z0E DISKAD PROFFSIG Dishwasher
Electrolux ESZ69300SX UltimateCare 700 Dishwasher
FISHER AND PAYKEL DD24DCTW9 Dishwasher
IKEA LAGAN Dishwasher
BOSCH SMV8ZDX86M Dishwasher
FISHER AND PAYKEL DD24STI9 Dishwasher
Miele PFD 101 Free Standing Dishwasher