INDESIT DI9E 2B10 UK Dishwasher
FIRST TIME USE
SALT, RINSE AID AND DETERGENT
ADVICE REGARDING THE FIRST TIME USE FILLING THE RINSE AID DISPENSER
After installation, remove the stoppers from the racks and the retaining Rinse aid makes dish DRYING easier. The rinse aid dispenser A should
be filled when when the dark optical indicator on the dispenser door C
becomes transparent.
elastic elements from the upper rack.
FILLING THE SALT RESERVOIR
The use of salt prevents the formation of LIMESCALE on the dishes
and on the machine’s functional components.
C
•
•
It is mandatory that THE SALT RESERVOIR NEVER BE EMPTY.
It is important to set the water hardness.
The salt reservoir is located in the lower part of the dishwasher (see Prod-
uct Description) and must be filled when the green float on the cap of the
salt reservoir is no longer visible..
B
A
1. Remove the lower rack and unscrew the
reservoir cap (anticlockwise).
2. Only the first time you do this: fill the salt
reservoir with water.
3. Position the funnel (see figure) and fill the salt
reservoir right up to its edge (approximately 1
kg); it is not unusual for a little water to leak out.
4. Remove the funnel and wipe any salt residue
away from the opening.
1. Open the dispenser B by pressing and pulling up the tab on the lid.
2. Pour in the rinse aid (max.110 ml), making sure it does not overflow
from the dispenser. If this happens, clean the spill immediately with
a dry cloth.
3. Press the lid down until you hear a click to close it.
NEVER pour the rinse aid directly into the appliance tub.
ADJUSTING THE DOSAGE OF RINSE AID
If you are not completely satisfied with the drying results, you can adjust
Make sure the cap is screwed on tightly, so that no detergent can get
into the container during the wash program (this could damage the wa- the quantity of rinse aid used.
ter softener beyond repair).
• Switch the dishwasher on using the ON/OFF button.
Whenever you need to add salt, it is mandatory to complete the
procedure before the beginning of the washing cycle to avoid corrosion.
• Switch it off using the ON/OFF button.
• Press button P three times - a beep will be heard.
• Switch it on using the ON/OFF button.
SETTING THE WATER HARDNESS
To allow the water softener to work in a perfect way, it is essential that
the water hardness setting is based on the actual water hardness in your
house. This information can be obtained from your local water supplier.
The factory sets the default value for the water hardness
• Switch on the appliance by pressing the ON/OFF button.
• Switch off the appliance by pressing the ON/OFF button.
• Hold down button P for 5 seconds, until you hear a beep.
• Switch on the appliance by pressing the ON/OFF button.
• The program indicator light of the current set level flashes.
• Press button P to select the desired hardness level (see WATER
HARDNESS TABLE).
• The program indicator light of the current set level flashes.
• Press button P to select the level of rinse aid quantity to be supplied.
• Switch it off using the ON/OFF button
Setting is complete!
If the rinse aid level is set to 1 (ECO), no rinse aid will be supplied.
A maximum of 5 levels can be set according to the dishwasher model.
The factory setting is specific to the model, please follow instruction
above to check this for your machine.
• If you see bluish streaks on the dishes, set a low number (2-3).
• If there are drops of water or limescale marks on the dishes, set a mid-
range number (4-5 ).
Water Hardness Table
°dH
FILLING THE DETERGENT DISPENSER
°fH °Clark
French degrees English degrees
Level
Soft
German
degrees
To open the detergent dispenser use the opening device D.
Introduce the detergent into the dry dispenser E only. Place
the amount of detergent for pre-washing directly inside the tub.
1
2
3
4
0 - 6
0 - 10
11 - 20
21 - 29
30 - 60
0 - 7
1. When measuring out the detergent
refer to the mentioned earlier infor-
mation to add the proper quantity.
Inside the dispenser E there are
Medium
Average
Hard
7 - 11
8 - 14
12 - 16
17 - 34
15 - 20
21 - 42
E
indications to help the detergent
dosing.
Very
hard
D
5
35 - 50
61 - 90
43 - 62
2. Remove
detergent
residues
from the edges of the dispenser
and close the cover until it clicks.
3. Close the lid of the detergent
dispenser by pulling it up un-
til the closing device is secured
in place.
• Switch off the appliance by pressing the ON/OFF button.
Setting is complete!
As soon as this procedure is complete, run a program without loading.
Only use salt that has been specifically designed for dishwashers.
If the salt container is not filled, the water softener and the heating
element may be damaged as a result of limescale accumulation.
The detergent dispenser automatically opens up at the right time ac-
cording to the program.
Usage of detergent not designed for dishwashers may cause mal-
function or damage to the appliance.
Using of Salt is recommended with any type of dishwasher detergent.
2
| General | Details |
|---|---|
| Name | INDESIT DI9E 2B10 UK Dishwasher |
| Make | INDESIT |
| Language | English |
| Filetype | PDF (Download) |
| File size | 5.88 MB |
(1 votes, average: 5.00 out of 5)
Loading...
INDESIT D2I HL326 Full Size Dishwasher
Indesit D2F HD624 A Separate Dishwasher
Indesit 869991713220 Dishwasher
INDESIT I0F D641A X Free Standing Dishwasher
Indesit I0F D641A Dishwasher
INDESIT DFE 1B19 14 Dishwasher
INDeSIT D2F Dishwasher
INDeSIT D2I HD524 A Dishwasher
INDESIT W11667630 B Dishwasher
InDeSIT IN2FE10CS90S Dishwasher
BOSCH SMV6HVX01I Dishwasher
FISHER AND PAYKEL DD60SHI9 Dish Drawer Dishwasher
BOSCH SMV4ECX10E-38 Dishwasher
COMFEE CDC22P Mini Dishwasher
FISHER PAYKEL DD60SCX9 Dish Drawer Dishwasher
FISHER PAYKEL DD60DDFHB9 Double Dishwasher
smeg STU8633 Fully Integrated Dishwasher
caple DI631 Dishwasher
BOSCH SMP6ZCW80S Dishwasher
BOSCH SMS4HMI07E-30 Dishwasher