SHARP SDW6506JS 24 Front Control Dishwasher
INSTALLATION INSTRUCTIONS
STEP 4: ADJUST LEVELING LEGS
1 Move the dishwasher close to the installation location and lay
it on its back.
STEP 5A: VERIFY EXISTING UTILITY
CONNECTIONS
WATER CONNECTION
2 Measure the height of the opening from the underside of
countertop to floor (lowest point).
• Check that the water line reaches to the front-left side of opening
where the water connection will be made as shown in Figure G.
3 Extend the leveling legs from the base of the dishwasher by the
length indicated in the following chart. Take into account any
built-up flooring which may need to be added to the rear foot
adjustment.
ELECTRICAL CONNECTION
• Check that the direct wire cable extends a minimum of 6" beyond
the front-right side of the opening, and is routed as shown in
Figure F.
NOTES:
• If the floor was raised in for the front of the dishwasher, account
for this difference when adjusting the rear leveling legs.
STEP 5B: PREPARE UTILITY CONNECTIONS
(IF NEEDED)
• Final leveling leg adjustments will be made following installation
into the opening.
PREPARE TO CONNECT POWER SUPPLY
Connect to the Power Supply using one of two Methods: Direct Wire
Cable (Method 1) or Power Cord (Method 2). Follow the instructions
specific to your installation. For both methods, a hole is drilled into
the right side of the cabinet, and the rough edges of the hole must be
smoothed or covered. For wood cabinets, sand the edge of the hole
until smooth. For metal cabinets, cover the edge of the hole with a
grommet (not provided).
WARNING
Adjust Leveling Legs
to Installation Height
ELECTRICAL SHOCK HAZARD
• Disconnect electrical power at the fuse box or circuit
breaker box before installing dishwasher.
• Failure to do so can result in death or electrical
shock.
LEVELING LEG ADJUSTMENT
Opening
Height
Front
Legs
Back
Legs
B
A
3
33 /4"
0
0
0
1
34"
/4"
1
1
/4"
1
/2"
34 /4"
1
1
3
34 /2"
1 /2"
/4"
A. Preferred locations
B. Optional locations
3
3
34 /4"
/4"
1"
1
35"
1"
1 /4"
FIGURE E
METHOD 1 - DIRECT WIRE
3
1 Drill a /4" (1.9 cm) hole into the right side cabinet, or the right
side of the back wall or floor of the opening. See Figure E for
preferred and optional locations.
NOTE: Wiring the dishwasher will be easier if the wire is routed
into the opening from the right side.
2 Smooth or cover rough edges of the hole that the wiring will
pass through.
8
| General | Details |
|---|---|
| Name | SHARP SDW6506JS 24 Front Control Dishwasher |
| Make | Sharp |
| Language | English |
| Filetype | PDF (Download) |
| File size | 1.37 MB |
(1 votes, average: 5.00 out of 5)
Loading...
SHARP SDW6506JS 24 Front Dishwasher
SHARP SDW6888JS Smart Dishwasher
SHARP QW-NA1BF47EI-EU Series Dishwasher
SHARP QW-NA24S42DI-EE Dishwasher
SHARP SDW6767HS Dishwasher
SHARP SDW6767HS Slide In Smart Dishwasher
SHARP SDW6767HS Smart Dishwasher
SHARP QW-NA26F39DI-EN Dishwasher
SHARP QW-NS1CF49EI-ES Dishwasher
SHARP SDW6757ES Dishwasher
FRANKE FDW 614 Integrated Dishwasher
LG LDTS5552D PrintProof Black Dishwasher
FISHER PAYKEL DD60SCX9 Sanitise Single DishDrawer Dishwasher
BOSCH SMS4EMI01E Standing Dishwasher
BOSCH SMS4ECI28E Dishwasher
BOSCH SGV43C53 Custom Panel ADA Compliant Dishwasher
KINGFISHER KF1000DW Deluxe Passthrough Dishwasher
BOSCH SMS8ZDI86M Dishwasher
Whirlpool WDT550SAPW Dishwasher
Zenith ZDWI601 Dishwasher