HOBART CLCS66e ML Series Dishwasher
TROUBLESHOOTING
SYMPTOM
POSSIBLE CAUSE
No Machine Operation.
1. Blown fuse or tripped circuit breaker at power supply.
2. Inspection door(s) not closed.
3. Conveyor has jammed.
4. The Auto-Timer may have timed out. Push START or insert rack.
5. If table limit switch is used, the switch may be tripped.
6. The machine is in Energy Saver Mode. Press STOP on the keypad to resume.
Dishes Not Clean.
1. Insufficient wash water. Drain obstruction causing an open drain condition.
Worn or torn drain O-ring allowing wash water to drain.
2. Missing end cap from wash arm.
3. Wash arm nozzle obstruction.
4. Worn or torn manifold O-ring allowing wash water to drain.
5. Loss of water pressure due to pump obstructions.
6.
Disconnect the electrical power to the machine and follow
lockout / tagout procedures. There may be multiple circuits. Be sure all
circuits are disconnected. Drain tank(s) and check for any obstruction at the
pump intake.
7. Incorrect water temperature. Check circuit breaker to electric heat supply, or main
steam valve, or gas supply valve. Make certain that valve is completely open.
8. Incorrect detergent dispensing. Contact your detergent sales representative.
9. Strainer pans or buckets need to be emptied and / or cleaned.
10. Tanks may need to be drained and filled with clean water.
Leaking Valve.
1. Foreign material preventing proper valve operation. A criticalperiod is soon after
installation when pipe compound or metal shavings may lodge at the valve seat.
If problem is with a solenoid valve, it is recommended that you contact your local
Hobart Service office.
Spotting of Silverware,
Glasses and Dishes.
1. Improperly loaded racks.
2. Incorrect final rinse water temperature (180°F or 120°F, minimum, page 24).
3. Loss of water pressure due to pump obstruction.
Disconnect the electrical power to the machine and follow
lockout / tagout procedures. There may be multiple circuits. Be sure all
circuits are disconnected.
Drain tank(s) and check for any obstruction at the pump intake.
4. Clogged wash arm nozzles.
5. Improper water hardness (3 grains per gallon or less is recommended).
6. Incorrect detergent for water type. Contact chemical supplier.
7. Clogged rinse nozzle(s).
8. Problem with Rinse Aid dispenser. Contact chemical supplier.
Low Final Rinse
Temperature
With Built-In Booster
Heater.
1. Tank float not 'up' permitting heat to turn on or float is malfunctioning.
2. Overtemp protector tripped. Contact Hobart Service.
3. Circuit breaker to heat system tripped.
4. Incoming water is below minimum temperature.
5. If your temperature control needs adjustment, or if there is a booster heater
failure, contact your local Hobart Service office.
NOTE: If symptom(s) persists after possible causes have been checked, contact
your local Hobart Service office.
– 37 –
| General | Details |
|---|---|
| Name | HOBART CLCS66e ML Series Dishwasher |
| Make | HOBART |
| Language | English |
| Filetype | PDF (Download) |
| File size | 2.18 MB |
(1 votes, average: 5.00 out of 5)
Loading...
HOBART AM16 Commercial Dishwasher
HOBART S.48820 Commercial Dishwasher
GE APPLIANCES GTW845 Dishwasher
Inventum VVW6046AB Dishwasher
LG LDTH7972SS Black Dishwasher
Westinghouse WSF6608KXB Sensor Wash Dishwasher
FISHER PAYKEL DD60SDFHX9 Dishwasher
BOSCH SMV4HMX01Z Dishwasher
SIEMENS 9001902343 Fully Integrated Dishwasher
Mueller DW-1800 Series 18 Inch Dishwasher
FAGOR 3LVF-423.1X Dishwasher
BOSCH SMU6ECI70S Dishwasher