Home >
HOBART > HOBART CLCS66e ML Series Dishwasher
× 1. Dishwashers (Model → Operation) 2. Important For Your Safety (For Your Safety → Read Before Operating) 3. General (Installation → Operation → Cleaning → Maintenance) 4. Installation, Operation And Care Of (General → Cl E And Cl E R Models → Tanks, Chambers, Frames, Legs And Adjustable Feet → Machines Can Be Ordered As Left-to-right Or Right-to-left Operation) 5. Chemical Sanitizing (Installation → Installation Codes → Adjust Machine Height And Level Machine → Dish Table Assembly) 6. Water Requirements (Water Conditions → Recommended Water Hardness) 7. Plumbing Connections (Drain Connection → Water Connections) 8. Required Incoming Water Temperature (Chemical Feeder Installations → Detergent Feed Port → Rinse Agent Feeder → Rinse Aid And / Or Chemical Sanitizer Feed Ports) 9. Steam Connection (when Machine Is Equipped With Steam Tank Heat) (Gas Connection (when Machine Is Equipped With Gas Tank Heat)) 10. Gas Specifications (Venting Requirements) 11. Exhaust Air Venting Requirements (Type Ii Canopy Hood → Exhaust Flow Requirements) 12. Pant-leg Vent Connections (Gas Heat Machines Must Be Provided With A Means To Exhaust → Mois T A I R E Scapes From Each End Of The Conveyor Type Dishwasher → The Mini-vent Hood Must Be Positioned A Minimum Of 18' Above The Flue Exit → For More Information, Refer To The National Fuel Gas Code, Ansi Z223.1, Nfpa54) 13. Cler-series (Cle-series) 14. Exhaust Flow Requirements (Length → Clearance → Height → Electrical Connections Dishwasher) 15. Single-point Electrical Connection (s.p.e.c.) Three-phase Only (Motor Rotation Three-phase Only) 16. Optional Equipment Control Connections (Detergent Feeder → Rinse Aid Feeder And/or Chemical Sanitizer Feeder → Vent Fan Control → Cler Energy Recovery Setup) 17. Open Door Of Dishwasher And Insert Dish Rack Upside Down In Final Rinse Zone To Activate Final Rinse Flow. Leave All Curtains In Place. 18. Adjust Pressure Regulator (Cold Water Pressure Regulator → Hot Water Pressure Regulator → Turn Main Power To Machine Off → Turn Main Power To The Machine On) 19. Cler Air Flow Adjustment (Adjust Damper) 20. Adjust Damper Shaft Until Steam Is Eliminated At This Area (Turn Main Power To Machine Off At Customer's Disconnect → Turn Main Power To Machine On At Customer's Disconnect; Machine Is Now Ready For Normal Operation) 21. Operation (Preparation → Latch → End Caps → Prewash Arm) 22. Cler Models (Ensure Drip Pan Is Installed In Energy Recovery Hood Assembly. → Curtain Installation → Final Rinse → Wash) 23. Single-tank Machines With Power Scrapper (Two-tank Machines With Power Scrapper → Final Rinse → Wash Scrapper → Css) 24. Two-tank Machines With Corner Scrapper (clcs) (Keypad And Display) 25. Filling The Dishwasher (Starting The Gas Heat Dishwasher (when Equipped With Gas Heat) → Minimum Temperatures) 26. Minimum Temperatures Using Low-temperature, Chemical Sanitizing (Single-tank Models → Two-tank Models → Alternative Temperature Display Names → Tank Temperature Alert) 27. Dishwashing (Loading Dishes → Operating The Dishwasher → Conveyor Dwell Feature → Clearing Conveyor Jams) 28. Optional Table Limit Switch (Auto-timer → Energy Saver Mode → Dirty Water Mode → Cleaning) 29. Remove Wash Arms (Clean Debris From Back Side Of Doors → Thoroughly Wash Out The Interior Of The Machine → Return All Standpipe(s), Strainer Pan(s) And Strainer Basket(s) → Insert The Upper Wash Arm(s) Straight Onto The Connector Pipe) 30. Reassemble (Deliming Recommendations → Clearing The 'delime Recommended' Message) 31. Dos And Don'ts For Your New Hobart Warewasher (Note: Failure To Follow Use, Care And Maintenance Instructions May Void Your Hobart Warewasher Warranty.) 32. Programming (Programming Security Levels → Operator O → Manager M) 33. Programming Instructions (Menu Display Prompts) 34. Entering The Parameters Menu (Display Message → Navigating The Parameters Menu) 35. Parameters Menu Table 1 (Sanitizing Mode → Auto-timer → Low Temp. Alert → Dirty Water Mode → Energy Saver Mode (esm)) 36. Communications Setup Menu (Maintenance → Vent → Lubrication → Service) 37. Troubleshooting (Symptom → No Machine Operation → Dishes Not Clean → Leaking Valve → Spotting Of Silverware, Glasses And Dishes) 38. Symptom (Continuous Rinse → No Wash Tank Heat, Tanks Not Heating → No Or Slow Fill → Leaking Vacuum Breaker) 39. Door(s) Open (Clear Conveyor Jam → Check Water Level → Reset Required → Delime Recommended) 40. Date (Scrapper Tank → Wash Tank → Power Rinse Tank → Final Rinse)
Close
HOBART CLCS66e ML Series Dishwasher
Two-Tan k Machines with Corner Scrapper (CLCS)
CLCS86 e , CLCS86 e R
CLeR
Unit
SCRAPPER
CSS
CSS
FINAL
RINSE
RINSE
WASH
CS
RIGHT TO LEFT
⇐
S
CO
L
L
M
L
CLeR
Unit
SCRAPPER
CSS
CSS
RINSE
FINAL
RINSE
WASH
LEFT TO RIGHT
CS
⇒
CO
S
L
M
L
L
L
L
S
919758 Long STD
919975 Long HTS
919509 Short
CO
M
936922 Carry Over
936428 Middle STD
936429 Middle HTS
936520 CS
M
CS
CSS
936931 CS Side
kEYPAD AND DISPLAY
76>,9ꢀ
+0:73(@ꢀ
: ; ( 9;ꢀꢁꢀ,5;,9ꢀ
:;67ꢀ
4,5<ꢀꢁꢀ+V^Uꢀ(YYV^ꢀ
*65=,@69ꢀ+>,33ꢀ
<Wꢀ(YYV^
Fig. 28
The controls are mounted on top of the dishwasher. The Keypad and Display are
mounted in front of the control box (Fig. 28).
– 24 –
General Details Name HOBART CLCS66e ML Series Dishwasher Make HOBART Language English Filetype PDF (Download) File size 2.18 MB
Download PDF Loading...
Loading...
